676964

BEKO HCA91531X Handleiding

29
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
- 27 -
ductor used to circulate hot air or for evacuating fumes from
other appliances generated by other than an electrical source.
Before proceeding with the assembly operations, remove the
anti-grease filter(s) (Fig.2.2 - Fig.3.2) so that the unit is easier to
handle.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• If the appliance is supplied with the small cupola M remove
it by releasing it as indicated in Fig.2.3 - Fig.3.3.
Before proceeding with the assembly operations, for easier
manoeuvrability of the appliance disengage the anti-grease
lter by pulling handle B as indicated in Fig.2.2 - Fig.3.2.
If one owns a model with perimeter suction panel, before
carrying out this operation, perform the following phases:
- Open panel C as indicated in Fig.2.1 - Fig.3.1.
- If one owns the version with three A panels release them from
the xing pins by pulling outwards (Fig.3.4) and then remove
them from safety pins N (Fig.3.4) placed inside the hood. To
put them back perform the operation in reverse order.
ATTENTION! During this disassembly and assembly
operation ensure to hold the panel securely to prevent
accidental falls.
• Wall mounting:
Trace the bottom side of the hood on the wall. Consider the
measurements shown in Fig.4A and minimum distance from
the cooking surface (Fig.4B).
- Position the xing template on the wall, making sure that the
line coincides with the line previously made on the wall.
- Mark the xing holes and cut them into the material (Fig.5).
- Fix the 2 top screws K and screw anchors (Fig.5), without
tightening them completely.
- Place the appliance against the wall, align it in horizontal
position and tighten screws K (Fig.6A).
- Once the adjustment has been completed, x the hood using
the 2 screws C (Fig.6B).
- When carrying out the xing operations, use only screws
and screw anchors suited to the type of wall (e.g. reinforced
concrete, plasterboard etc.).
- If the screws and screw anchors are supplied with the
appliance, make sure that they are suited to the type of wall
to which the hood must be xed.
•Installationofmodelswithoutdecorativeducts:
Extractorhood
- Unclip the canopy M and remove the grille E (Fig.7).
- Pass the power supply cable through the slot in the canopy
M, as indicated in Fig.9A.1.
- Taking the grommet H, position it between the power cable
and the slot (Fig.9A.2).
- Connect the exible hose L (not supplied) to the hood (Fig.9B).
- Re-position the small cupola M paying attention that it is
hitched perfectly to the xing pins G (Fig.9B).
• Filtering version:
- Unclip the canopy M and remove the grille E (Fig.7).
- Pass the power supply cable through the slot in the canopy
M, as indicated in Fig.8.1.
- Taking the grommet H, position it between the power cable
and the slot (Fig.8.2).
- Fix the small cupola M and the grille E making sure that is it
perfectly hooked on to the fastening pins G (Fig.8).
• Optional accessories:
This model may have decorative ducts as optional accessories
- ask your retailer for information.
Before installing decorative ues it is necessary to remove
the small cupola M and loosen the 4 screws Q that lock the
fastening pins G as shown in Fig.11.
•Installationofmodelswithdecorativeducts:
Extractorhood
Make sure the electrical power supply is within the measure-
ments of the decorative connector. Adjust the width of the
support bracket of the top connector (Fig.10.2). Then x it
to the ceiling so that it is on the same axis as the hood using
screws A and observing the distance from the ceiling shown in
Fig.10.1. Connect ange F to the air exhaust hole using exible
hose L (Fig.12A). Slide the top connector inside the lower duct
and place this on the body (Fig.12B). Pull out the top duct as
far as the bracket and secure it using screws B (Fig.10.2). To
transform the hood from a ducting version into a ltering
version, ask your dealer for the charcoal lters and follow the
installation instructions.
•Filterhood:
Please note:
The lters must be ordered from your dealer as an accessory.
- To transform the hood from the SUCTION version to the
FILTERING version, charcoal lters must be ordered from your
dealer as an accessory. Two types of kit are available, one with
non-renewable lters (Fig.13) and the other with renewable
lters (washable) (Fig.14). Unlike traditional carbon lters,
this carbon lter can be washed and reactivated for approxi-
mately 12-15 times. With normal hood use, this lter should
be cleaned once every 2-3 months. The lter can be washed
into a dishwasher at the highest temperature using a standard
dishwasher detergent. After washing, dry the lter in the oven
at 100°C for 10-15 minutes to reactivate it. The lter will retain
its odour-absorbing capacity for three years, after which it will
have to be replaced.
- If a bracket is found in the packaging like that indicated in
Fig.14 loosen the screws already installed inside the hood and
install the bracket using the previously-removed screws.
- To replace re-usable carbon filters Y, remove the brackets
from their seat, pulling them outwards (Fig.14).
- If your product is not supplied with the bracket, it means that
the active charcoal lter cannot be renewed (Fig.13). These
must be applied to the suction unit inside the hood, centring
them in it and turning them 90° until they snap into place
(Fig.13).
USE AND MAINTENANCE
• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
•Theanti-greasefilter is responsible retaining the grease
particles suspended in the air, therefore it is subject to clogging
with variable frequency according to the use of the appliance.
- To prevent the danger of possible fires, at least every 2
months one must wash the anti-grease filters by hand using
non-abrasive neutral liquid detergents or in the dishwasher
at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
•Theactivecarbonfilters are used to purify the air that is
… 29 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw BEKO HCA91531X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van BEKO HCA91531X in de taal/talen: Alle talen als bijlage per email.

De handleiding is 5,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info