Handleiding BEKO HBG70 (pagina 17 van 28) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans)

556806

Verklein

Vergroot

Pagina terug

1/28

Pagina verder

- 17 -

the 4 sleeves C and 4 screws D as indicated.

•Fixingtothewall

Drill the holes A respecting the distances indicated (Fig.2).

Fix the appliance to the wall and align it in horizontal posi-

tion to the wall units. When the appliance has been adjusted,

denitely x the hood using the screws A (Fig.5). For the

various installations use screws and screw anchors suited to

the type of wall (e.g. reinforced concrete, plasterboard, etc.). If

the screws and screw anchors are provided with the product,

check that they are suitable for the type of wall on which the

hood is to be xed.

•Fixingthedecorativetelescopicue

Warning! Caution! If your appliance model features the

lower connector with a tab, before xing it in place bend

the tab inwards using a pair of pliers, as illustrated in gure

5, step1.

Arrange the electrical power supply within the dimensions of

the decorative ue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening. Adjust the width of the support

bracket of the upper ue (Fig.3). Then x it to the ceiling using

the screws A (Fig.3) in such a way that it is in line with your hood

and respecting the distance from the ceiling indicated in Fig.2.

Connect the ange C to the air exhaust hole using a connection

pipe (Fig.5 - Stage 2). Insert the upper ue into the lower ue.

Fix the lower ue to the hood using the screws B provided

(Fig.5 - Stage 2), extract the upper ue up to the bracket and

x it with the screws B (Fig.3). To transform the hood from a

ducting version into a ltering version, ask your dealer for the

charcoal lters and follow the installation instructions.

•Filteringversion

Install the hood and the two ues as described in the paragraph

for installation of the hood in ducting version. To assemble the

ltering ue refer to the instructions contained in the kit.

If the kit is not provided, order it from your dealer as accessory.

The lters must be applied to the suction unit positioned inside

the hood. They must be centred by turning them 90 degrees

until the stop catch is tripped (Fig.8).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The effective performance of the cooker hood depends on

constant maintenance; the anti-grease filter and the active

carbon filter both require special attention.

•Theanti-greasefilter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the filter to become saturated depends on

the way in which the appliance is used).

- To prevent potential fire hazards, the anti-grease filters

should be washed a minimum of every 2 months (it is

possible to use the dishwasher for this task).

- After a few washes, the colour of the filters may change. This

does not mean they have to be replaced.

If the replacement and washing instructions are not followed,

the anti-grease filters may present a fire hazard.

•Theactivecarbonfilters are used to purify the air which

is released back into the room. The filters are not washable

or re-usable and must be replaced at least once every four

months. The active carbon filter saturation level depends on

the frequency with which the appliance is used, the type of

cooking performed and the regularity with which the anti-

grease filters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with denatured

alcohol or neutral, non-abrasive liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination. Extended use

of the light reduces the average duration of the bulb.

•Replacinghalogenlightbulbs(Fig.6)

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

•Commands(Fig.9) mechanical the key symbols are explained

below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III.

•Commands(Fig.10) luminous the key symbols are explained

below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes (*).

•If your appliance does not have the INTENSIVE speed

function, press key E for two seconds and it will be activated

for 10 minutes after which it will return to the previously set

speed. When the function is active the LED ashes. To interrupt

it before the 10 minutes have expired press key E again.

• By pressing key F for two seconds (with the hood switched

o) the “clean air” function is activated. This function switches

the appliance on for ten minutes every hour at the rst speed.

As soon as this function is activated the motor starts up at

the rst speed for ten minutes, During this time key F and key

C must ash at the same time. After ten minutes the motor

switches o and the LED of key F remains switched on with

a xed light until the motor starts up again at the rst speed

after fty minutes and keys F and C start to ash again for ten

minutes and so on.

By pressing any key for the exclusion of the hood light the

hood will return immediately to its normal functioning (e.g.

if key D is pressed the “clean air” function is deactivated and

the motor moves to the 2nd speed straight away. By pressing

key B the function is deactivated).

(*) The “AUTOMATIC STOP TIMER” delays stopping of the

hood, which will continue functioning for 15 minutes at the

operating speed set at the time this function is activated.

•Activecarbon/greaseltersaturation:

- When button A ashes at a frequency of 2 seconds, the

grease lters must be cleaned.

- When button A ashes at a frequency of 0.5 seconds, the

carbon lters must be replaced.

After the clean lter has been replaced, the electronic memory

must be reset by pressing button A for approximately 5

seconds, until the light on the button stops ashing.

BEKO HBG70 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info