815458
98
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
11 | Installation EN Operating manual Fireplace inserts slied flat + II
98
Calibration: The calibration (see above) of the controls is carried out when the controls are connected
to the mains or the WLAN is changed, but only if the flue gas temperature is below 80 ° C. In the pro-
cess the control software detects where the positions 0% and 100% shutter opening are on its fireplace
insert. After the controls have detected the two maximum positions, they run to the 0% shutter open-
ing (if the correct program has been chosen) and switches into the Standby phase.
This process requires approximately 10 minutes. Should the flue gas temperature be above 80°C, no
calibration run is carried out. The controls use the data from the last calibration run that was carried
out.
The programming of the controls includes various “Eco” and “Normal” combustion curves. Each of
these two modes is available with the “sliding opening” and “sliding closing” function.
Program overview
Selection wheel Mode Function
Position 0 - Shutter opening, always 60%
Position 1 Normal sliding opening
Position 2 Eco sliding opening
Position 3 Normal sliding closing
Position 4 Eco sliding closing
Selecting the program
Fig.76: Unplugging the power supply
1) Remove power supply from the socket.
2) Remove the three screws and open the control unit
housing.
1
Fig.77: Selecting the program
On the circuit board is a selector switch (1) that by default is
set to position “0”.
3) Select program by setting the arrow of the selector
switch to position 1, 2, 3 or 4 (see “Program Overview”
table.
4) Before closing the controls again, carry out a fresh cal-
ibration by plugging the power supply back in.
ðIf you have selected the correct “sliding closing” or
“sliding opening” function, after the calibration the
controls must complete close the shutter.
ðShould you notice that you have chosen the wrong
program, you can change this in the service menu
of the app.
APP
The InsertControl function can be monitored using the app on iOS and Android Smartphones. To do
so, first load the “InsertControl” app from the iTunes Store or Google Play on to your Smartphone.
When it is connected to the circuit, InsertControl creates a WLAN with the name “ABR_xxxxxxx”
(xxxxxxx = serial number of the controls). You must connect your Smartphone to this network (pass-
word: 12345678). After the app is started, the connection is automatically established.
If desired you can then connect the app to another WLAN (in the app’s settings menu). Please note
that a new calibration run for the controls will then be started.
98

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II in de taal/talen: Engels als bijlage per email.

De handleiding is 14.06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II Gebruiksaanwijzing - Deutsch - 124 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info