519915
16
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
15
Before the first start-up
L
To achieve flawless functioning of the machine, please follow the
instructions listed:
Place the saw at a location which meets following conditions:
outdoor
secured against slipping
free of vibrations
even
free of tripping hazards
adequate light
Check the following prior to use:
Defective connecting lines (cracks, cuts, etc.).
Never use defective lines!
Proper working condition of the safety guard.
Correct splitting wedge setting (see also Fig. 15).
Perfect condition of the saw blade.
The push stick must be within easy reach.
Never use saw blades that are cracked or have become deformed.
Do not use saw blades made of high-speed steel.
Always stand to the side of the danger zone (saw blade) when working at
the bench.
Start-up
Checking the safety devices
(before each starting):
- Lift and lower the safety guard to check that it can be moved freely. In its
rest position it must fully cover the saw blade and rest on the saw table.
(See also “Possible faults”.)
- Check the switch by turning it on and off.
Do not use any device where the switch can not be switched on and off.
Damaged switches must be repaired or replaced immediately by the
customer service.
- Brake
The saw blade must stand still within 10 seconds after it was switched off.
The brake is defective if this time is exceeded. The saw must then be
repaired by the manufacturer or a workshop appointed by the
manufacturer.
- Pushstick
Replace defective pushsticks by new ones.
Rotating direction of the saw blade
L
Ensure that the rotational direction of the saw blade is the same as
the rotational direction given on the guard (14)
.
The rotating direction of three-phase motors
can be changed by inserting a screwdriver in
the connector collar provided for this purpose
and turn left or right while exerting a light
pressure to adjust the correct rotating direction.
Selection of saw blades
Observe the splitting wedge thickness "S"; it is etched into the
side of the splitting wedge.
The splitting wedge must not be thinner than the saw blade, and not
thicker than the kerf width produced by the blade.
The rating plate specifies maximum and minimum saw blade
diameters, as well as the hole diameter.
Do not use saw blades that are designed for a lower max. speed
(see identification on the saw blade) than the motor speed (see the
technical data).
L Mains connection
Compare the voltage specified on the rating plate (on the side of the table
board), e.g. 230 V, with the mains voltage. Connect the circular saw bench to
a correctly earthed socket outlet.
Alternating-current motor:
Schuko (earthed) socket, mains voltage 230 V, with earth-leakage circuit
breaker (FI switch 30 mA).
Three-phase motor:
CEE socket, 3-pin + N + PE, mains voltage 380 V or 400 V, with earth-
leakage circuit breaker (FI switch 30 mA).
Use connecting and extension cables in conformity with IEC 60245
(H 07 RN-F) with a conductor cross-section of at least:
-1.5 mm² for a cable length of up to 25 m.
-2.5 mm² for a cable length exceeding 25 m.
2,5 mm² for BTK/BTH 500
L Main fuse:
400 450 500
BTK/BTH 16 A inert 16 A inert 20 A
On/Off switch
Switching on
- Open the switch cover.
- Press the green button ( I )
L
The device cuts off automatically in case of power failure.
To restart, first push the red button ( 0 ) and then again the green
button ( I ).
Switching off
Press the red button ( 0 ) or the red button of the yellow switch
cover.
Single-phase variant (230 V)
Three-phase variant (400 V)
Press to open
the switch
cover.
ON
OFF
LEDs
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atika BTH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atika BTH in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 3,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info