519288
17
Verklein
Vergroot
Pagina terug
1/85
Pagina verder
16
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points.
Local regulations especially regarding protective
measures – must be observed.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer
service points.
Use only original spare. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
A
A
s
s
s
s
e
e
m
m
b
b
l
l
y
y
Screw on both side parts (1+2).
For each side part you require:
2 cup square screws M 8 x 40
2 combi nuts M 8
Screw on the transverse joint (4).
For the connection you require:
4 cup square screws M 8 x 10
4 combi nuts M 8
Put the pre-assembled device unit on the side
parts.
Fix first one side with each 2 round-head screws
M 5 x 16 and hexagon nut M 5.
Now fix the other side.
Then, fasten the four screw connections.
Put on the extraction hose (7).
Fasten the extraction hose by refastening the screw
on the hose clip (17) a few revolutions.
Put on the saw dust collecting bag (14).
Fasten the saw dust collecting bag by attaching the
quick release fastener (6).
Hang in the bag suspension (9).
Put on the filter bag (15).
Fasten the filter bag by attaching the quick release
fastener (6).
Hang in the filter bag.
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Check that the machine is completely and correctly
assembled.
Put the saw dust extraction system on a place which
meets the following requirements:
firm and even ground
free of risks of stumbling
sufficient light and air conditions
Before using the machnine, make sure each time that
there are no faulty connections (tears, cuts, etc.)
Do not use any defective cables.
there are no damage at the machine (see safety
advices)
all screws are tight
Mains connection
Compare the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the
machine to the relevant and properly earthed plug.
Use a shockproof plug, mains voltage 230 V with
residual current circuit breaker (FI switch 30 mA).
Only use connection cables with sufficient diameters.
Mains fuse: 10 A
Static charge
The complete extraction system is assembled of non-
electro-conductive components.
Do not replace synthetic parts by metallic parts.
Particularly, the extraction hose must not feature a
metallic coil.
When the extraction hose is fastened on electro-
conductive parts (e.g. metallic suction hoods or
tubes) these must be grounded for the discharge of
possibly appearing electrostatic energy.
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be
repaired or replaced immediately by the customer
service.
Switch on
Press the green button
( I ) on the switch.
Switch off
Press the red button
( 0 ) on the switch.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atika ABS 2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atika ABS 2000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info