519873
14
Verklein
Vergroot
Pagina terug
1/123
Pagina verder
Setting the clearance.
Switch on the device.
There is an adjustment device on the right hand side of the plastic housing. To adjust the distance turn the adjusting knob (D)
clockwisely so that the screw (C) moves toward the cutting roller. Turn until fine aluminium chips are falling from the ejection slot.
13
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Each time before starting maintenance work:
Switch off the motor and pull out the mains plug.
Wear protective gloves to prevent injury.
The cutters will not come to a standstill immediately after cut-off. Before starting any service work wait until all parts are sta-
tionary.
Be sure to have removed any tools from the machine after completion of service work.
Generally garden shredders require little maintenance. To maintain their efficiency and a long life, observe the following:
Keep vent slits clean and free from obstructions.
Check the locking screws (tighten where necessary).
Clean the device after shredding.
To clean your product only use a warm moist cloth and a soft brush.
Never use cleaning agents or solvents. Otherwise the device may be damaged irreversibly. Plastic parts may be corroded by chemi-
cals.
Do not clean the machine with running water or high-pressure cleaners.
After each operation treat bare metal parts with an environment-compatible biodegradable spray oil to protect them against corro-
sion.
the cutting roller and shaving plate are expendable parts, though with normal use and correct adjustment they have a service life of
many years
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
a
a
l
l
f
f
a
a
u
u
l
l
t
t
s
s
Before each fault elimination:
Switch off device.
Wait for standstill of the device.
Pull out mains plug.
Fault Possible cause Remedy
Motor does not start - Rotation selector switch on position “0”
- No power supply
- Mains cable defective
- Machine overloaded (motor protection)
- Switch off device and switch over direction of rotation
selector switch.
- Check fuses
- have these checked (electrician)
- Allow the device to cool down.
Press the
1. reset button (motor protection)
2. green button I to restart.
Motor hums but does not
start
- Cutting roller blocked
- Capacitor faulty
- Switch off the device.
Turn the direction of rotation selector switch into
position
. Switch on device until the jam has been
cleared. Switch device off again. Turn back the
direction of rotation selector switch to position
.
- Bring machine to manufacturer or authorised work-
shop for repair
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Atika 2300 W bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Atika 2300 W in de taal/talen: Nederlands, Engels, Frans, Italiaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info