673158
11
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
Inst.296 Viron eVo Series Pool & Spa Heater V07_16
12
600
Approved gas
termination cowl
1500
Upper grille for fresh air
ventilation
Lower grille for fresh air
ventilation
Do not install spa blowers in the same room as a gas heater. This is potentially dangerous to spa users.
Do not store chemicals or fuel in the same room as the gas heater. This may cause fire or explosion.
When installing in a garage the Viron Series Heater must be installed 450 mm above floor level.
ELECTRICAL CONNECTION
The heater is supplied with a standard 10 amp 3 pin plug for connection to a 240V 10 amp GPO. All pool or spa
equipment connected to mains power should be protected by an RCD circuit breaker.
GAS CONNECTION
The gas connection is on the right hand side of the heater. A 22mm M.I. connection is provided for gas line
connection. An approved manual shut off valve must be installed in the gas fitting line before the heater.
The gas fitting line should be installed by an authorised person and comply with local regulations and Australian
Standard code AS/NZ 5601. The gas line from the meter will usually be of a larger size than the gas inlet
connection.
The heater gas valve has a built in pressure regulator and ⅛” pressure test point. On starting the heater, a
manometer must be used and the supply inlet pressure checked while the heater is running against the heater
data plate. Incorrect inlet pressures may void warranty and may result in service charges, should service be
required. Gas valves are preset and should only be adjusted by trained Astral Pool technicians.
PRESSURE SWITCH ADJUSTMENT
The Viron Pool Heater incorporates a water pressure switch which allows the burner to operate only when the
circulating pump is operating. The pressure switch is designed to operate with the heater installed up to 1.2
metres above or below the surface level of the pool or spa. For installations outside these limits, a flow switch
should be installed.
It is imperative that the following be undertaken by the person who is commissioning (first starting) your pool or
spa heater. On initial start up of the heater it may be necessary to adjust the water pressure activation switch.
This switch is located behind the top right hand side panel and is screwed into the water manifold. The pressure
switch is a safety device, designed to allow operation of the heater only when the circulating pump is on and there
is sufficient water flow through the heater. It must shut the heater down immediately the pump is switched off.
To check the operation of the switch:
1. Connect the heater to mains power supply and turn power on. The thermostat should not yet display “θ”.
2. Turn on pump. The thermostat should now display “θ”.
3. Turn pump off. The thermostat should no longer display “θ”.
4. If display does not respond in this way, adjust the pressure switch as detailed below. If display responds
correctly, perform a final check with the heater operating.- See the section below titled “Starting the heater”
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Astralpool Viron eVo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Astralpool Viron eVo in de taal/talen: Engels als bijlage per email.

De handleiding is 0,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info