628507
47
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
T
ROUBLESHOOTING
ASPI Digital -
The Sound of DSP
Technical Support: 404.892.3200 45
Acoustic Gain
Failure
Acoustic gain failure can be caused through a number of mechanisms:
1. The most common is excessive amplification of the remote (reference) signal at
the local Zone output. This may be explained as follows. If the reference signal
is too low coming into the EF1210, the room audio amplifier will need to be
turned up to compensate and bring the room audio to an acceptable level. For
example, if the reference signal is 12 dB too low (just barely lighting the first
green LED on the R
EMOTE
S
IGNAL
L
EVEL
M
ETER
), the room audio will need to
be amplified by approximately 12 dB to bring it to a reasonable listening level.
This adds 12 dB to the acoustic gain, which will most likely cause it to exceed the
amplifier acoustic gain limit (See “Check Acoustic Gain” on page 31.). This sit-
uation can be remedied by proper calibration of the Reference input signal.
2. Another common cause of acoustic gain failure is excessive microphone amplifi-
cation. For example, if a microphone is "hot" by 6 dB, then the reflections of the
Zone output signal which are picked up by the microphone will be amplified by 6
dB more than necessary. This adds 6 dB to the acoustic gain, which may be suf-
ficient to cause acoustic gain problems. This situation could easily arise if, for
example, the conferencing equipment is set up so that participants are too far
from the microphone. In such a situation, after correct microphone setup the
local microphone audio level may be too low because of the distance from the
talker to the microphone. The microphone audio will most likely also be muddy
and reverberant. The installer or user may try to solve these microphone audio
quality problems by turning up the microphone amplification, thus adding to the
acoustic gain. This problem can be remedied by proper microphone selection
(pickup pattern, directionality) and placement, coupled with proper microphone
calibration.
3. A third common cause of acoustic gain problems is excessive coupling between
loudspeaker audio and microphones. This can be addressed by reducing the
microphone coupling, either by positioning microphones so that their pickup pat-
terns are biased away from the loudspeaker audio (and direct reflections of loud-
speaker audio), repositioning loudspeakers, or reducing the loudspeaker
amplification.
In summary, it can be seen from the above that any amplification applied between the
reference input and the microphone inputs can add to acoustic gain problems. To
avoid problems, ensure that the Reference input signal (as reflected on the R
EMOTE
S
IGNAL
L
EVEL
M
ETER
) is not too low, and the microphone input signal (as reflected
on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
) is not too high. Run the built-in EF1210 Acous-
tic Gain test to verify that you do not have acoustic gain problems (See “Check
Acoustic Gain” on page 31.).
In-Conference
Quick Check
If you experience residual echo problems during a conference, you can quickly check
that the reference and microphone levels are calibrated and not causing acoustic gain
problems by observing the signal level meters as follows.
While the remote end is speaking and everyone on the local end is quiet, observe the
activity on the R
EMOTE
S
IGNAL
L
EVEL
M
ETER
. Remote speech should illuminate the
first yellow (0 dB) LED regularly, and the second (+3 dB) LED occasionally. Step
through the microphone input channels by repeatedly pressing the I
NPUT
S
ELECT
front panel button while the remote end is speaking (the local end must be silent dur-
ing this check), and observe the activity on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
for each
microphone channel in response to the remote talker. If any microphone channel
exhibits greater signal level activity than that shown on the R
EMOTE
S
IGNAL
L
EVEL
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info