628507
40
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EF1210 U
SER
M
ANUAL
38 http://www.aspi.com Copyright © 1999, All Rights Reserved
O
PERATING
THE
EF1210
U
SING
THE
EF1210 W
ITHOUT
RS-232 C
ONTROL
Changing Level
Display on
I
NPUT
and
R
EMOTE
LED Meters
When the EF1210 is in normal operating mode, pushing the I
NPUT
S
ELECT
button will
allow you to see levels of each input channel on the I
NPUT
LED meter. The green
LED corresponding to an input channel will light if the levels of that channel are cur-
rently displayed on the I
NPUT
LED meter. In the same way, pushing the R
EF
S
ELECT
button will allow you to see the levels of each reference input on the R
EMOTE
LED
meter. A yellow LED will indicate which reference (AEC A or AEC B) is displayed
on the meter.
Adjusting Volume in
Zones
The reference LEDs (AEC A or AEC B) do double duty. They not only indicate
which Reference Input is currently displayed on the R
EMOTE
LED meter, but also
indicate which Zone Output is affected when the L
EVEL
A
DJUST
buttons are pressed.
The AEC A LED indicates that Z
ONE
A’s volume is being adjusted by the L
EVEL
A
DJUST
button. The AEC B LED indicates that Z
ONE
B’s volume is being adjusted
by the L
EVEL
A
DJUST
button. The output levels can be adjusted up to 6 dB above and
12 dB below the nominal zone output level. The nominal zone output level is 6 dB
below the level selected in Calibration Step 2: Calibrating Zone Outputs.
Adjusting Playback
Levels
The A
UX
I
N
input and R
EC
output signals are preset to -10 dBV signal levels. The
level of the A
UX
I
N
signal may be adjusted during normal operation to compensate for
low or high audio level from an external playback device.
1. During normal operation, press and hold the A
UX
I
N
L
EVEL
/S
ETUP
button while
using the L
EVEL
A
DJUST
buttons to adjust the level of the playback signal. The
level-adjusted A
UX
I
N
signal is mixed with the A
MIX
I
N
signal (nominally 0dBu)
and sent to the T
O
CODEC connector. It is also mixed with the AEC A signal
and played over the Zone A output.
Muting
To mute channels while using the EF1210 without RS-232 control, for push-to-talk
microphones for example, we suggest using the mute control capability on the mixer
rather than using a microphone with mute built inside it. The AEC will perform bet-
ter using this method because it allows the speech to be processed inside the EF1210
before being muted instead of totally cutting off the speech so that the AEC has to
readapt when the microphone comes on again.
Splitting zones
Calibrate using calibration procedures. When using more than one zone, refer to
“Calibration Step 5: Zone/Reference Setup” on page 34 to associate each microphone
input channel with a reference. If you are using two reference signals (Reference A
and Reference B), Input Channel 1 must be associated with Reference A (AEC A)
and Input Channel 8 must be associated with Reference B (AEC B). The other 6
microphones can be associated with either reference
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info