628507
8
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
EF1210 U
SER
M
ANUAL
6 http://www.aspi.com Copyright © 1999, All Rights Reserved
Q
UICK
I
NSTALLATION
Installation of the EF1210 involves two procedures: hardware installation, and cali-
bration.
H
ARDWARE
I
NSTALLATION
Hardware installation involves the following steps:
1. Set rear panel DIP switches to select Line or Mic level and enable phantom
power for each microphone input channel, and to select ASPI Bus Device ID if
necessary. See “Configuration” on page 15.
2. Connect input and output signals (See “Connecting the EF1210 to other equip-
ment” on page 19):
Connect the 8 Mic/Line Inputs to microphones.
Connect the 8 Line Outputs to the inputs of a mixer.
Turn off Phantom Power on automixer.
Connect Zone Output(s) to amplifier(s) or powered loudspeaker(s).
Connect AEC Reference Inputs to the T
O
AEC output of an EF200 or to the
output of a CODEC.
If you wish to use the EF1210’s built in Playback/Record mixer feature, con-
nect A
MIX
I
N
, A
UX
I
N
, T
O
CODEC, and R
EC
as directed in “Playback/
Record” on page 22.
3. If you are using an RS232 remote control device, connect it to the RS-232
R
EMOTE
C
ONTROL
port; if you are controlling multiple ASPI devices, connect
them using the ASPI Bus ports (See “Connecting the ASPI Bus” on page 26).
4. Connect the external power supply.
C
ALIBRATION
Calibration of the EF1210 involves a sequence of five calibration steps to configure
the input and output levels of the EF1210 to match those of the equipment to which it
is connected. The EF1210 can be calibrated either from the front panel or by using a
computer. Please refer to “Calibration” on page 27 for more detailed information on
the Calibration procedure. Correct calibration is essential for satisfactory operation of
the EF1210, so please take the time to familiarize yourself with the details of the Cal-
ibration procedure by reading “Calibration” on page 27.
For front panel calibration, enter Calibration mode by pressing and holding the A
UX
I
N
L
EVEL
/S
ETUP
and I
NPUT
S
ELECT
front panel buttons for 2 seconds. In Calibration
mode, the S
ETUP
LED will blink to let you know which setup step you are currently
executing. Press the A
UX
I
N
L
EVEL
/S
ETUP
button to move from one Calibration step
to the next. When you have finished Calibration step 5, press the A
UX
I
N
L
EVEL
/
S
ETUP
button again to exit Calibration mode; any changes that you made will be
saved as the default power-on settings when you exit the Calibration procedure.
Caution!
The EF1210 is designed to maintain a 1/4” (6.35 mm) air circula-
tion clearance above the enclosure. Do not stack or install
EF1210s in such a way as to defeat this clearance, block the side
vent holes, or otherwise impede air circulation around the
EF1210.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aspi EF1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aspi EF1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Aspi EF1210

Aspi EF1210 Aanvulling / aanpassing - English - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info