702729
6
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
- 6 -
Setting auto-gain:
Tone Indication Result Cause Remedy
One pulse
(Beep) Optimal sensitivity has been set OK - -
Continuous tone Optimal sensitivity cannot be set NG 1. Beam is interrupted once 1. Remove any blocking items or
(20 sec) the cover is replaced. ensure that the hand is not breaking
the beam when the cover is held in a
temporary position.
2. Beams are misaligned and 2. Check the beam power setting at
sensitivity attenuation LED lights the transmitter with the cover
attached and readjust the beam
alignment.
Tone indicator:
Test signal Alignment tone switch Other condition Description
Beam alignment ON Receiver cover detached - Reception strength monitored. Tone pitch
increases as reception improves.
Note: No tone is given if the sensitivity
attenuation LED is lit or if the receiver cover is
attached.
Walk test ON For approx. 5 minutes after - Tone is linked to the alarm LED. Both trip
gain is locked. simultaneously.
Alarm memory ON Set to manual memory. - Beep is initiated if an alarm condition occurs.
Note: This configuration is not recommended
for most security applications. The tone could
alert the intruder to detection.
Auto-gain lock ON/OFF After receiver cover is - A short tone indicates that the lock set.
attached. A continuous tone (20 sec.) indicates
readjustment.
7. TROUBLESHOOTING
Problem Possible cause Remedy
Operation LED does not light. 1. No power supply 1. Turn on the power.
2. Bad wiring connection or broken wire (short) 2. Check and correct the wiring.
Alarm LED does not light when 1. No power supply 1. Turn on the power supply.
the beam is broken. 2. Poor wiring connection or broken wire (short) 2. Check and correct the wiring.
3. Beam is reflected on to another object and 3. Remove the reflecting object or change the beam
sent to the receiver. direction.
4. Two beams are not broken simultaneously. 4. Break two beams simultaneously.
5. The beam interruption time is shorter than the 5. Adjust the beam response time.
set response time.
Alarm LED continues to light. 1. Beam alignment is out. 1. Check and adjust again
2. Shading object between the transmitter and 2. Remove the shading objects
receiver. 3. Clean the optics with a soft cloth
3. Unit optics are dirty. 4. Readjust to the same channel
4. Frequency channel is not compatible between
the transmitter and receiver
Intermittent alarms. 1. Bad wiring connection. 1. Check again.
2. Change of supply voltage. 2. Stabilize supply voltage.
3. Shading object between transmitter and 3. Remove the shading object.
receiver. 4. Change location of the installation.
4. A large electrical noise source, such as a 5. Stabilize.
power machine, is located near the transmitter 6. Clean the optics with a soft cloth.
and receiver. 7. Check and adjust again.
5. Unstable installation of transmitter and receiver 8. Increase the response time. (impossible in a
6. Dirty transmitter or receiver optics. location where the intruder can run at full speed.)
7. Incorrect alignment. 9. Set the beam power switch at H and make the
8. Small animals may be passing through the unit gain locked with the receiver cover
two beams. detached.
9. Beam power switch is set to L, which does not
keep enough sensitivity allowance.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech PB601 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech PB601 in de taal/talen: Engels, Frans, Zweeds als bijlage per email.

De handleiding is 0,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info