702739
2
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
- 2 -
Acoustic Glass Break Detector
Installation Manual
APPLICATION
The GS930 is an acoustic glass break detector designed to detect break-
ing glass from framed windows in the perimeter of building. The detector
can safely and reliably detect glass breakage on both small and large ob-
jects as well as on single or multiple glazed objects.
INSTALLING THE DETECTOR (FIGS. 1 TO 7)
Select a mounting position for the detector that is on a wall or ceiling adja-
cent to, or across from, the glass surface being monitored;
Only use for indoor installations;
Do not expose to any direct airflow;
Must have a line-of-sight view of all glass surfaces to be
protected;
Locate it no further than 8.5 m and not less than 1.0 m from the glass;
Mount it at least 0.15 m away from an adjacent wall or ceiling and at
least 1.8 m from the floor;
Can be temporarily mounted to conduct an initial functional test;
Must be permanently mounted on a stable and vibration-proof surface;
When closing the cover, ensure that the tamper contact spring is fed
into the recess in the cover.
"
In VDS-approved systems, the detector cover must be sealed with
an additional screw (enclosed with the detector) (Fig. 8).
SPECIAL NOTES
Do not mount the detector on the same wall as the glass surface being
protected.
If the glass is covered by inside shutters or sound deadening drapes,
or where exhibits or display items conceal the detector, check that the
detector is operating correctly before permanently mounting it (see
Functional testing during installation
).
Do not use only one detector to protect glass in multiple rooms even if
the range test indicates the detector is operating correctly. This is a
precaution in case doors or other partitions are later placed between
the rooms.
Do not use in 24 hour-monitoring zones.
PROGRAMMING (FIG. 6)
Power /status LED (Green) Jumper J3
Off Open
On Closed
When closing the pins of jumper J3, the green LED remains lit when power
is applied to the detector. The green LED will extinguish for one second
when a loud sound occurs in the upper frequency rage, noting a pre-trip
condition. However, an alarm is not activated unless the other sound
characteristics required by 3 x 3 technology are also present.
Alarm LED (Red) Jumper J4 RESET Input
Flashing for 2.5 sec Open Open
Latched after alarm Closed Open
Follows alarm relay Closed Permanently LOW
RESET Closed With LOW
When an alarm occurs, the red alarm LED flashes for 2.5 sec. When
latched, the LED will indicate a new alarm by flashing for 2.5 sec. and re-
latching afterwards. The latched LED can be reset by applying a LOW
signal to the RESET input.
FUNCTIONAL TESTING DURING INSTALLATION (FIGS. 5 & 9)
High-frequency range testing:
Remove the detector cover;
Apply power and press the test button (SW2) once. The red and green
LEDs will start to quickly flash alternately. The detector is now ready for
high-frequency range testing;
Replace the detector cover;
Hold the tester near the surface of the glass to be protected and aim the
speaker at the detector from the furthest point of the glass. If there are
closed curtains, hold the tester behind them;
Slide the tester switch to TEST position, and a simulated glass break
sound will be produced every 10 seconds. If the glass is within range, the
flashing LED will latch for 2.5 sec. At the same time the alarm relay is
opened so that the appropriate detection line on the alarm control unit
will trip.
Low-frequency range testing:
To enter this mode while in the high-frequency test mode, press the
test button (SW2) a second time. The LEDs will now flash alternately at
a slower rate.
A sharp blow of the hand or other firm object to a framed hollow wall,
ceiling or door will cause the flashing LEDs to latch for 2.5 sec. and the
alarm relay to open.
IMPORTANT: This test is not a range check.
The test mode lasts 5 minutes after which the detector automatically resets
to the normal operation mode. To manually exit the test mode, press the test
button until the LEDs stop flashing.
FUNCTIONAL TEST IN NORMAL OPERATION
The detector must be in the normal operation mode with the cover in
place.
Hold the GT-2 tester directly against the glass surface to be protected
while aiming the loudspeaker towards the detector. Set the mode
selection switch to RUN.
Slap the glass to be protected with your flat hand. The unit automati-
cally produces a loud simulated glass break sound.
If the detector has been correctly installed, this should trigger an alarm.
SPECIFICATIONS
Input voltage 9 to 15 VDC
- Max ripple 2 pp
- Voltage monitoring 6.4 V ± 0.4 V
Current consumption:
- Standby, no status LED 12 mA
- Standby, with status LED 14 mA
- Alarm, with alarm LED no status LED 9 mA
- Alarm, with latched alarm LED and status LED 15 mA
Alarm output:
- Semiconductor relay opens on alarm
- Contact load rating 100 VDC / 120 mA
- Series resistance 35 ohm
Tamper contact 100 VDC / 500 mA
Sensitivity automatic adjustment
Max. range 8.5 m radius
Area of the surface to be monitored min 0.3 x 0.3 m, max 6 x 6m
Volume of the room to be monitored min 22 m³, max 245 m³
Recommended glass thickness:
- Plate 3 mm to 6 mm
- Tempered 3 mm to 6 mm
- Wired 6 mm to 8 mm
- Laminated 6 mm to 8 mm
Environmental class II -10 °C to +55 °C
EN
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech GS930 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech GS930 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info