702727
6
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Installation
5
Copyright 1996 WARNING-Opto-Elektronik GmbH & Co Produktions KG
changes reserved
3 Installation
Installation procedure
1. For installation within moulded columns first of all prepare ground plate and moulded columns (see
3.4 installation with moulded columns)
2. For outdoor application install B-boards and heaters inside of the equipment (see 2.5
heaters)
3. Install the equipment at provided installation position (see 3.3 installation of the equipment)
4. Wire the equipment (see 3.2 wiring of the equipment)
5. Align transmitter and receiver (see 4 alignment)
6. Configuration of the system (see 5 putting into operation)
7. Check up system’s functioning (see 6 completion work)
3.1 VdS-Installation
The following has to be considered for the installation of a VdS-equipment:
1. The VdS-approval is only valid for indoor application
2. The alarm response time is to fix to 20 ms and not allowed to be altered
3. Never use a disqualification circuit when VdS is applied
4. Never use a heater for VdS application
5. Use only shielded cables with twisted pairs
6. The shielding of the supply line between transmitter and receiver are connected with
minus potential on both sides
7. The shielding of the supply line to the central control unit must be connected with ground
potential
8. The housings are to be connected with ground potential
9. For intended drilling work at moulded columns the devices have to be removed
completely
10. After fixing seal screws either with adhesive lead or lead wire
11. For installation of moulded columns they have to be equipped with cover contact
12. The jumpers at the transmitter and receiver are to be plugged in (pre-adjustment)
according to 5 putting into operation
13. Never apply any surface mirror at VdS-operation
3.2 Wiring of the equipment
Use only shielded cables with twisted pairs. The shields of the supply lines are to be connected as
described under VdS-application 3.2.1 wiring diagram.
Transmitter Receiver
1
2
3
4
5
6
7
+ / operating voltage
- / operating voltage
vacant (for shield, with – connected)
sabotage (only for single devices)
sabotage (only for single devices)
vacant (for closing resistance)
reference
1
2
4
5
6
7
8
9
10
3
11
+ / operating voltage
- / operating voltage
vacant (for shield, with - connected)
sabotage (only for single devices)
sabotage (only for single devices)
vacant (for closing resistance)
reference
NO
COM
vacant (for closing resistance)
technical interference
The sabotage contact of moulded columns is not brought out (the clamps 4 and 5 at receiver and
transmitter are not occupied).
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aritech DO560 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aritech DO560 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info