Handleiding Ariston Pro 1 Eco (pagina 13 van 18) (Engels)

719590

Verklein

Vergroot

Pagina terug

1/18

Pagina verder

USER INSTRUCTIONS

Reset/Diagnostics

When one of the malfunctions described above occurs, the appliance will enter its “fault status” and all LEDs on the

control panel will ash simultaneously.

Reset: to reset the appliance, switch the product o and on again using the

button (Ref. A). If the cause of the mal-

function disappears immediately following the reset process, the appliance will resume normal operation. If this is not

the case, all the LEDs will continue to ash; contact the Technical Assistance Centre.

Diagnostics: to enable the diagnostic function, hold the

button (Ref. A) for 5 seconds. The type of fault is indicated

by ve LEDs (Ref. 1 >5) according to the following scheme:

LED Ref. 1 – Internal P.C.B. malfunction;

LED Ref. 2 – Anode malfunction (in models tted with active anode);

LED Ref. 3 – NTC 1/NTC 2 temperature sensors broken (open or short-circuited);

LED Ref. 5 – Water overheating detected by an individual sensor;

LEDs Ref. 4 and 5 – General overheating (P.C.B. malfunction);

LEDs Ref. 3, 4 and 5 – Operation without water.

Exit the diagnostic function by pressing the

button (Ref. A) or wait for 25 seconds.

"Thermal disinfection cycle" function (anti-legionella)

The anti-legionella function is activated by default. It consists of a heating/maintenance cycle of the water at 60°C for 1h

so as to carry out thermal disinfection action against the relevant bacteria.

The cycle starts at the rst ignition of the product and after each re-ignition which follows a lack of mains power. If the

product always work at a temperature below 55°C, the cycle is repeated after 30 days. When the product is o, the anti-

legionella function is not active. If the appliance is switched o during the anti-legionella cycle, the product turns o

and the function is not completed. At the end of each cycle, the operating temperature returns to the value set previ

ously by the user. The activation of the "anti-legionella cycle" is displayed as a normal temperature setting at 60°C. (Led

Ref. 4). To permanently disable the anti-legionella function simultaneously hold down the "ECO" and "+" buttons for 3

sec.; conrming deactivation the led 40° will C ash rapidly for 4 sec. To reactivate the anti-legionella function, repeat

the operation described above; to conrm the reactivation of the led (Ref. 4) will ash rapidly for 4 sec.

Adjusting the temperature and activating the functions (Fig. 3)

Press the button (Ref. A) to switch on the appliance. Set the desired temperature by using the “+” and “-” buttons to

select a level between 40°C and 65°C. During the heating phase, the LEDs (Ref. 1> 5) corresponding to the temperature

reached by the water so far remain lit in a xed manner; all subsequent LEDs (up to the set temperature) ash progres-

sively. If the temperature drops, for example after hot water has been used, the heating is reactivated automatically and

the LEDs between the last xed light and the light corresponding to the set temperature will resume ashing progres-

sively. The rst time the product is switched on, it will be set to a temperature of 60°C (Led Ref. 4).

In the event of a power failure or if the product is switched o using the button (Ref. A), the most recently set tempera-

ture remains memorised. During the heating phase, a slight noise may be produced as a result of the water heating

process.

The LED remains ON during heating.

ECO FUNCTION

The Eco function is activated/deactivated by pressing the corresponding button. If the function is activated the led will

be switched on. The Eco function aims to produce hot water by learning the user habits. So, for the rst week ever the

product memorises the tappings and the periods in which those tappings take place. From the following weeks the wa

ter heating is performed regarding what was learned previously. If the user wants to reset the function and start a new

learning period, it is necessary to press the ECO button for 3 seconds (the eco led will appear blinking).

If during Eco function, PLUS or MINUS button are pressed the function will be deactivated.

SHOWER READY

The Shower Ready LED (B, Fig. 3) indicates whether there is hot water for at least one shower. The quantity of hot water

is determined by internal parameters and varies according to the model.

MAX FUNCTION

The Max function (C, Fig. 3) is activated/deactivated by pressing the corresponding button. If the function is active, the

LED will be lit. The Max function temporarily sets the set-point temperature to 65°C by bypassing the previous operat-

ing mode (if the Eco function is active, the self-learning function is temporarily interrupted and deactivates on its own

once the set-point is reached).

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Ariston Pro 1 Eco Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Ariston Pro 1 Eco

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info