719969
28
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
27
!
!
!
GB
!
This appliance was designed to be installed only inside buildings in compliance with the applicable norms in force.
Furthermore, installers are requested to keep to the following advice in the presence of:
- Damp: do not install the appliance in closed (unventilated) and damp rooms.
- Frost: do not install the appliance in areas where the temperature may drop critically and there may be a risk that
ice may form.
- Sunlight: do not expose the appliance to direct sunrays, even in the presence of windows.
- Dust/vapours/gas: do not install the appliance in the presence of particularly aggressive atmospheres such as acidic
vapours, dust or those saturated with gas.
- Electrical discharges: do not install the appliance directly on electrical supplies that arent protected against sudden
voltage jumps.
See warning no. 26
See warning no. 9 - In the case of walls made of bricks or perforated blocks, partition walls featuring limited
static, or masonry different in some way from those stated, you first need to carry out a preliminary static
check of the supporting system.
Install the appliance using the special bracket provided in the box, fastening it using 2 screws/Rawlplugs
measuring 6 mm in diameter.
See warning no. 10
Local norms could set forth restrictions regarding the installation in a bathroom environment. Therefore keep
to the minimum distances foreseen by the applicable norms in force.
The appliance should be installed as close as possible to the point of use to limit heat dispersion along the
piping.
See warning no. 20
Installing the appliance
Before making the plumbing connection, you must arrange for the system to be cleaned thoroughly to eliminate
any residue or dirt that could compromise the proper operation of the water heater.
Connect the water heater inlet and outlet to resistant pipes or pipefittings, as well as to the operating pressure, the
temperature of the hot water that could at times reach well over 80°C. We advise against the use of materials that
cannot withstand such high temperatures.
We recommend you use dielectric joints for the electrical insulation of the appliance from the water mains.
Connect the inlet pipe (marked with a blue rubber washer) and the outlet pipe (red rubber washer) to the corresponding
pipes of the system. Tighten couplings E using a pair of spanners as illustrated in fig. 4
In the event of low mains pressure values, install the appliance at no more than one metre above the tap (fig. 3) and
no more than 2 metres form the side of the latter.
Should these distances be greater than the recommended values, you must include an air valve on the hot water pipe.
Fill the appliance up and let the water flow out of the tap for a few seconds.
The water flow rate, with the tap turned on fully, should not be more than 5 l/min; for this reason, in accordance with
DIN 44531 norm, you should adjust the small valve (fig. 5) to limit the water flow.
In the presence of particularly hard waters, there will be a considerable and rapid formation of limescale inside the
appliance, with a consequent loss in efficiency and damage to the electric heating element.
Plumbing connection
Electrical connection
For greater safety, have qualified personnel carry out a careful inspection of the electrical system, ensuring it complies
with the applicable norms in force, because the appliance manufacturer will not be held responsible for any damage
caused by the lack of earthing of the system or for faults in the electricity supply.
See warning no. 24 - Check that the system is suitable for the maximum power absorbed by the water heater
(please refer to the data plate) and that the cross-section of the electrical connection cables is suitable, and
no less than 1.5 mm
2
.
The power supply cable (type H05 W-F 3x1.5, 8.5 mm in diameter) should be inserted in the corresponding hole (X
fig. 6) situated in the vicinity of the control knob and feed it until it reaches the thermostat slots (T fig. 6). The electrical
connection should be made directly on the terminals (D fig. 6) of the thermostat (respect the L-N polarity).
The appliance is fitted with a cable and plug. For installations without a plug, use a bipolar switch in conformity with
the applicable norms in force (fused with a minimum contact opening of 3 mm).
The appliance must be earthed and the earth wire (yellow-green colour) should be fastened to the special faston on
the heating element and marked with the (PE fig. 6). Secure the power supply cable in place using the special
cable clamp provided with the appliance
See warning no. 11
!
!
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ariston Piccolo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ariston Piccolo in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 1,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info