454498
28
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
24
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Ready, steady, go!
Make sure the
wash cycle has
ended before
removing the
dishes!
Did you know that?
Your dishwasher is equipped with
sophisticated software allowing it
to express itself in 8 different lan-
guages, and using a sensor to as-
sess how dirty the dishes are to
optimise the "auto" wash cycles.
Keep an eye on the display, it's your
dishwasher's means of communi-
cations with you where it can send
you simple messages to inform you
as to what it's doing. It can even
request that you carry out a few
simple tasks, and it can signal any
oversights on your part.
First of all.
Turn on the water tap completely
and press ON-OFF button "A". the
display "B" comes on and the words
corresponding to the wash cycle to
which the knob is set scrolls along
it. If the knob is set to Reset, then
the word "Pause" scrolls along. In
both cases, your appliance is await-
ing instructions.
Selecting the wash cycle.
Turn knob "D" until the reference
notch on the knob corresponds with
the number or symbol for the cycle
you wish to set (have a look at the
wash cycle table on page 26). The
name of the wash cycle selected
scrolls along the display. Now press
the Start button "M" and, after a
few seconds, you will hear a short
beep: the wash cycle has begun and
the display indicates the cycle
phase under way. The counter "L"
will indicate the amount of time
left until the end of the wash cycle.
The dishwasher informs
you.
During operation, your dishwasher
tells you where it is at. In fact, the
following phases of the wash cycle
under way scroll along your display
screen: pre-wash, wash, rinses, dry-
ing.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Turn the knob un-
Do not forget to
press "Start" to
start the wash
cycle.
til it reaches the Reset position and,
after a few seconds, you will hear
4 beeps. The word "Pause" scrolls
along the display. This indicates
that all the settings have been can-
celled. You are now free to re-set
the correct wash cycle. Press
START to start the wash cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by pressing the
ON-OFF button, the display comes
off. Insert the dish you had forgot-
ten and press the ON-OFF button
again. The display turns on and the
cycle will start up from where you
interrupted it.
Finished?
The end of the wash cycle is sig-
nalled by a double beep, and a flash-
ing "washing finished" comes up on
the display. Press the ON-OFF but-
ton as well, thus cutting off the elec-
tricity supply to the appliance.
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam. Empty
the upper rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then re-
starts when the electricity comes
back on or when you shut the door.
Everything is under control!
You want to wash on
one rack only? Remem-
ber to use half the
amount of detergent.
Your dishwasher also allows you to
wash half a load (choosing on
which rack), to save water and elec-
tricity. Before setting any wash
cycle whatsoever, press button "F".
Each time this button is pressed,
you will hear a beep, and symbol
(upper rack) and symbol
(lower rack) appear on indicator
"N". Press it once more to reset the
rack selection and the dishwasher
will consequently wash on both
racks.
How to eliminate the
drying phase
Should you wish to reduce the
length of the wash cycle and per-
fect drying is not your main prior-
ity, you can eliminate the drying
phase completely.
First of all, select the upper or lower
rack if you wish, as well as any
delayed start. Turn the knob to se-
lect the wash cycle: if the wash
cycle includes a drying phase, press
button "H" to eliminate the latter.
The name of the wash cycle scrolls
along the display screen, followed
by the words "no turbo dry". Press
the button once more to reinstate
the drying phase.
You decide when it
starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired. Press button "E" and
you can delay the start of the wash
cycle by 1 to 24 hours. Each time
you press the button, the number
of hours will appear in sequence on
the counter: you choose when you
want the cycle to start.
Now indicator light "I" comes on
to indicate at all times that your
dishwasher is awaiting instructions.
On the counter, the countdown to
the delayed start has begun.
If opening the
door soon after
the end of the
programme, or
during it, stand
away from the
dishwasher, to
avoid possible
injury from hot
steam.
28

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ariston-LSE-830-ST

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ariston LSE 830 ST bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ariston LSE 830 ST in de taal/talen: Nederlands, Engels, Portugees, Turks als bijlage per email.

De handleiding is 7,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info