Handleiding Ariston CDE12X (pagina 15 van 20) (Engels)

23732

Verklein

Vergroot

Pagina terug

1/20

Pagina verder

Margherita - Iinstructions for installation and use

ARGHERITA

Mounting the Parts onto

the Face of the Machine

- Mount the hinge supports onto

the face of the machine,

positioning the hole indicated by

the arrow in fig. 1 towards the

inside of the face and using the

type C screws.

- Mount the magnetic plate on

the opposite side, at the top,

using the two type B screws.

- Place the spacer illustrated in

fig. 4/B between the appliance

front and the magnet receiver.

Using the Drilling

Template

- To trace the positions of the

holes on the left-hand side of the

panel, align the drilling template

to the top left side of the panel

using the lines traced on the

extremities as a reference.

- To trace the positions of the

holes on the right-hand side of

the panel, align the drilling

template to the top right side of

the panel.

- Use an appropriately sized router

to mill the holes for the two

hinges, the rubber plug and the

magnet.

Mounding the Parts onto

the Wooden Panel (Door)

- Insert the hinges into the holes

(the movable part of the hinge

must be positioned facing away

from the panel) and fasten them

with the 4 type A screws.

- Insert the magnet into the top

hole on the opposite side of the

hinges and fasten it with the two

type B screws.

- Insert the rubber plug into the

bottom hole.

The panel is now ready to be

mounted onto the machine.

Mounting the Panel into

the machine

Insert the nib of the hinge

(indicated by the arrow in fig. 2)

into the hole for the hinge and

push the panel towards the front

of the machine. Fasten the two

hinges with the type D screws.

Fastening the plinth

guide

If the machine is installed at the

end of a set of modular cabinets,

mount either one or both of the

guides for the base molding (as

shown in fig. 8). Adjust them for

depth based on the position of

the base molding, and, if

necessary, fasten the base to the

guides (fig. 9).

This is how to assemble the

plinth guide (fig.8):

Fig. 6 Fig. 7 Fig. 9

Adjusting the appliance

height

The height of the appliance can

be adjusted (from 815 mm to

835 mm), by turning the 4 feet.

Should you require the appliance

to be placed higher than the

above height, you need to use the

following accessories to raise it

to up to 870 mm:

- the two crossbars (G)

- the 4 feet (H)

- the 4 screws (I)

- the 4 nuts (L)

then perform the following

operations (fig. 11):

remove the 4 original feet, place

a crossbar G at the front of the

appliance, fastening it in place

using screws I (screwing them in

where the original feet were) then

insert the new feet H.

Repeat the same operation at the

back of the appliance.

Now adjust feet H to raise or

lower the appliance from 835

mm to 870 mm.

Once you have reached the

desired height, lock nuts L onto

crossbar G.

Fig. 11

To adjust the appliance to a

height between 870 mm and 900

mm, you need to mount strip M,

adjusting feet H to the required

height.

Insert the strip as follows:

loosen the three screws N

situated at the front of the Top

cover of the appliance, insert

strip M as shown in fig. 12, then

fasten screws N.

Accessories provided for

the height adjustment

The following can be found inside

the polystyrene lid (fig. 10):

2 crossbars (G),

1 strip (M)

the following can be found inside

the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Fasten angle P using screw R,

insert plinth guide Q into the

special slot and once it is in the

desired position, lock it in place

using angle P and screw R.

Inserting the machine

into the Cabinet

- Push the machine into the

opening, aligning it with the

cabinets (fig. 6).

- Regulate the adjustable feet to

raise the machine to the

appropriate height.

- To adjust the position of the

wooden panel in both the vertical

and horizontal directions, use the

C and D screws, as shown in fig. 7.

Important: close the lower part of

the appliance front by ensuring

that the plinth rests against the

floor.

Fig. 10

Fig. 12

Fig. 8

570

815

540

595

820 ÷ 900

600 m

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Ariston CDE12X Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Ariston CDE12X

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info