Handleiding Argo Fancy (pagina 3 van 13) (Engels)

805110

Verklein

Vergroot

Pagina terug

1/13

Pagina verder

V 05/21

FANCY

This product is only suitable for well insulated spaces or

occasional use.

OPERATING INSTRUCTIONS

Read the instructions carefully before installing and operating the appliance or performing

maintenance operations. Observe all the safety instructions; failure to observe the instructions may

cause accidents and/or damages. Store these instructions for future reference.

ELECTRIC CONVECTOR HEATER

IP24

V 05/21

GENERAL SAFETY INFORMATION

 Use this convector only as outlined in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock or

injury to persons.

 This convector is designed for domestic use. It must not be used for

commercial or industrial purposes.

 Ensure that the mains voltage complies with that indicated on the

convector data plate (230-240V~ 50-60 Hz).

 This appliance can be used by children aged from 8 years and

above and people with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

 Children shall not play with the appliance.

 Cleaning and user maintenance shall not be made by children

without supervision.

 Remove the convector from its packaging and check that it is in good

condition before use. Keep any plastic bags away from children.

 Check the cord and plug before using the convector to ensure that

they have not been damaged during transport.

 This product is not a toy.

 Children under the age of 3 must be kept away if not continuously

supervised.

 Children aged between 3 and 8 must only turn the appliance on / off

as long as it has been placed or installed in its normal operating

position and that they receive surveillance or instructions regarding

the safe use of the appliance and understand the dangers.

 Children between 3 and 8 years of age must not insert the plug,

adjust or clean the appliance or carry out maintenance by the user.

CAUTION - Some parts of this product can become very hot and

cause burns. Particular attention has to be given where children

and vulnerable people are present.

WARNING: In order to avoid hazard due to inadvertent resetting of

the thermal cut-out, this appliance must not be supplied through and

external switching device, such as a timer, or connected to a circuit

that is regularly switched on and off by the utility.

WARNING: do not use the convector with a controller or any

other external device that activates the appliance automatically,

V 05/21

as there may be a risk of fire if the fan heater is covered or

incorrectly positioned.

 The appliance is equipped with an IP24 degree of protection

and can be used in private bathrooms in zone 2.

Do not use the convector in the immediate vicinity of bathtubs,

showers, washbasins or swimming pools.

 Disconnect the mains power when the appliance is not used or for

cleaning operations.

 To disconnect the convector, set the selector to 0 and remove the

plug from the socket. Pull on the plug only. Do not pull the cord.

 Avoid placing fingers or foreign objects in the air inlet/outlet grilles,

as this may lead to electric shock or fire and may damage the

convector. To avoid the risk of fire, do not block the grilles or tamper

with them in any way while the convector operates.

 Do not use the convector if the cord or plug is damaged. If the

power cable is damaged, it must be replaced by the manufacturer or

its technical assistance service or in any case by a person with a

similar qualification, in order to prevent any risk.

 Do not place any objects on the cord and do not bend it. During

operation, the cord must be entirely unwound.

 It is not advisable to use extension cords, as these may overheat

and cause the risk of fire. Do not use a single extension cord to

operate more than one convector.

 The convector heats up significantly during operation. Risk of burn.

To avoid injury, do not allow skin to come into contact with a hot

surface. Use the handle to move the convector. Keep flammable

materials, such as furniture, cushions, blankets, paper, cloths,

curtains and suchlike at least 1 m from the front and back

V 05/21

 Do not immerse the cord, plug or any other element of the panel in

water or other liquids.

 Do not touch the plug or convector with wet hands.

 Avoid using the convector in dusty environments or in the presence

of flammable vapors (e.g. in workshops or garages).

 Do not place the convector above or near another heat source.

WARNING: AVOID COVERING THE CONVECTOR TO PREVENT IT

FROM OVERHEATING.

The symbol below signals the above warning:

 The convector may cause risk of fire if, while in operation, is covered

by or comes into contact with flammable material including curtains,

drapery, blankets, etc. KEEP THE CONVECTOR AWAY FROM

THESE MATERIALS.

 Do not insert and avoid accidental insertion of any external objects

into the ventilation or discharge outlets as this may lead to electric

shock, fire or damage the convector.

 A convector contains parts that generate arcs or sparks. It must not

be used in potentially dangerous areas such as areas at risk of fire

or explosion, or areas loaded with chemical substances or humidity.

 Do not use the convector on soft surfaces such as beds, where the

grilles may be covered. Always stand the convector on a flat, stable

surface when in operation, in order to prevent it from overturning.

Arrange the cord in such a way that the convector and other objects

do not rest on it. Do not run the cord under carpets. Do not cover the

cord with blankets, carpets or similar materials. Place the cord far

away from busy areas, or in a place where it cannot be accidentally

pulled-out.

 Never position the convector where it may fall into a bath or other

containers of water.

 Never position the convector on a wet floor.

 In any case, the adjustment switches must never be accessible by

anyone in a bath or shower.

 The heating appliance must not be positioned immediately below a

power outlet.

 The socket must be earthed.

V 05/21

 Do not allow the electric cord to touch the metal structure of the

convector when it is hot or in operation, in order to avoid the high

temperatures ruining the cord.

 Do not operate the convector outdoors. Do not use the convector in

front of or near an open window.

 WARNING: do not use the convector with an external controller

or any other external device that activates the convector

automatically, as there may be a risk of fire if the convector is

covered or incorrectly positioned.

 Upon initial start-up, the convector may emit a slight, harmless smell.

This smell is a normal effect of the initial heating up of the internal

heating elements, and should not recur later on.

 Do not attempt to repair, disassemble or modify the convector. The

convector does not contain parts that can be repaired by the user.

 Turn the switch off and unplug before carrying out any maintenance

work or moving the convector. Always unplug from the socket when

the convector is not in use.

 WARNING: ALWAYS UNPLUG WHEN CARRYING OUT

MAINTENANCE WORK OR MOVING THE CONVECTOR.

 Do not place anything on the convector; avoid placing wet garments

on the convector.

 Turn the appliance off if unattended in order to avoid accidents.

 If the convector is not used for prolonged periods, disconnect the

plug, replace the convector in its box and store it in a dry, ventilated

place.

 Ensure that the air inlet /outlet are not close to walls or curtains when

the convector is in use, so as to avoid obstructing the convector and

hampering its efficiency.

 Should you hear an abnormal noise or detect an unusual smell when

using the convector, cease use and unplug immediately.

 Do not expose the elderly or children to a continuous flow of air.

 Do not use the convector if it has been damaged or dropped.

 Always use the convector with feet fixed. Do not use any other feet

except the ones supplied with the product.

WARNING: THE ON/OFF SWITCH IS NOT THE ONLY MEANS TO

DISCONNECT THE POWER SUPPLY. ALWAYS PULL OUT THE

PLUG FROM THE SOCKET IN THE EVENT OF MAINTENANCE

OPERATIONS, WHEN MOVING THE PANEL OR WHEN NOT IN

USE.

V 05/21

DESCRIPTION OF PARTS

HOW TO INSTALL THE APPLIANCE

The convector can be used on the floor, after assembling the feet, or alternatively it can be wall-mounted using the

specific accessories supplied.

MONTARE I PIEDINI IN DOTAZIONE

A. Floor portable using: how to assemble the feet supplied

The convector is packed without feet. These must therefore be assembled before using the appliance.

Assemble the feet as shown in the figure and put the convector in an upright position. Position the unit on a flat,

stable surface and follow the indications here below:

1. ON/OFF switch

2. Rear bracket

3. Control panel

4. Front panel

5. Feet

V 05/21

1. Turn the convector upside down 2. Insert the feet. The longest

part must be positioned behind

on the rear the convector.

3. Tighten the wing nuts on the feet.

B. Wall-mounting: how mount the convector onto the wall

The convector packaging contains all the accessories necessary for wall-mounting.

To wall-mount, proceed as follows. The appliance has already attached the bracket to the rear of the product, so

remove it from the convector following these steps:

1. Unscrew the two screws located on the upper part of the two vertical bars of the wall bracket.

2. Pull out the wall bracket by pressing down on the top of the two vertical bars of the wall bracket.

3. Remove the wall bracket completely from the convector.

After removing the bracket, proceed as follows (figure below):

A. By placing the bracket against the wall, mark on the wall with the pencil the points where to make the holes to

insert the fisher. Respect the minimum distances of the convector from the walls.

B. Drill the 8mm diameter holes in the wall and insert the fisher.

C. Attach the bracket to the wall and screw the supplied screws into the fisher.

D. Position the unit straight so that the holes are aligned with the bracket and insert the parts of the bracket into the

holes on the back in the upper part of the convector. Make sure that the convector is firmly hooked to the bracket

by gently pulling it.

Tighten the screws at the top of the convector firmly.

V 05/21

Make sure that the convector is placed at least 30 cm from the floor and that the distance from walls and objects is

respected, as indicated in the figure below:

CONTROL PANEL

TOUCH CONTROL PANEL ON THE UNIT

LED ON CONTROL PANEL OPERATIVE BUTTONS ON CONTROL PANEL

① Standby: on/off

② Heating Mode

③ Open window function

④ Comfort Mode

⑤ ECO Mode

⑥ Timer

Connect the power cord to an appropriate power outlet (230-240V / 50-60Hz).

The appliance emits a beep, this means that the convector is ready for use.

The LED lights up on the control panel.

Then press the ON / OFF switch located on the side of the unit and move the button to position I to turn on the device. If,

on the other hand, you want to switch off the convector, turn the button to position O.

Standby

Heating Mode

Open window function

Button +

Button -

Timer

V 05/21

ON / OFF - STAND-BY BUTTON

After connecting the power cable and turning on the unit with the side power button, press this button on the control

panel to turn on the fan heater. Press this button again to turn off the appliance.

TIMER BUTTON AND WEEKLY SETTING

Press and hold this button on the control panel for 3 seconds to select the timer and weekly setting. The display shows

"d", then press the and keys to select the days of the week in the following sequence:

1 Monday

2 Tuesday

3 Wednesday

4 Thursday

5 Friday

6 Saturday

7 Sunday

Press the button to confirm the desired day and set the time, the display will show

Then press and buttons to select the hour, then press the button to confirm it.

Appears on the display

Press and buttons to set the minutes, then press the button to confirm.

NB: If the power supply is removed, the weekly programming and the timer are reset to the factory settings.

HEATING MODE BUTTON

Press this button on the control panel to activate the heating modes, in the following circular sequence:

- Comfort Mode: Press the buttons and to set the temperature from 5°C to 35°C

- ECO Mode: Press the buttons and to set the temperature from 1°C to 31°C

- Anti-frost Mode: The target temperature is 7°C. The temperature can’t be adjusted.

- P1/P2/P3 Pre-set heating program

- Note: If the clock and day setting are not finished, the first time to enter P1/P2/P3 program setting, it is requested

to set day and clock setting in advance.

P1: (Monday-Sunday) Unadjustable program

P2:(Monday-Friday) Unadjustable program

V 05/21

P2 :(Saturday-Sunday) Unadjustable program

P3: (Monday-Friday) Adjustable program

P3:(Saturday-Sunday) Adjustable program

- P3 adjustable program setting

1. When under P3 mode, press over 3 secs to enter day setting.

2. The screen displays , press and to set from (Monday-Sunday). Press to confirm and

enter hour setting

3. The screen displays , press and to set from 00-23). Press to choose heating mode for every

hour (Comfort mode or ECO mode )

4. Repeat the operation until you have completed the schedule of every hour and every day.

Note: After setting heating mode for hour 23, press to come back to day setting.

Note: when screen displays , press finish all setting with display of .

OPEN WINDOW FUNCTION

Press one time and the indicator light is on. If open window function is activated, the indicator light

keeps flashing and stops heating.

Press again to quit open window function and back to previous working situation.

TIMER OFF BUTTON

Press one time, the indicator light is on. And the screen display “0 H” and keeps flashing. press and

to set timer from 0-24 hours. Press again to confirm setting.

V 05/21

MAINTENANCE AND STORAGE

ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE.

IMPORTANT: DO NOT SUBMERGE THE CONVECTOR IN WATER.

Cleaning the outside surface of the appliance

Turn the switch off and unplug before carrying out any maintenance work or moving the appliance.

Use a soft cloth to remove any dust from the convector.

If the convector is excessively dirty, use a soft cloth moistened with water and a mild detergent at a temperature lower than

50°C. Let the convector dry completely before use.

Do not use corrosive detergents or solvents such as petrol. Do not wash the appliance with water. Do not use oils,

chemical substances or other items to clean that may damage the surface.

Use a vacuum cleaner to remove dust from the air inlet/outlet grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging, in

a cool and dry place.

V 05/21

Table 2

INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Annex II - Ecodesign requirements - Requirements for product information -

COMMISSION REGULATION (EU) 2015/1188 of 28 April 2015 implementing Directive 2009/125/EC of the European

Parliament and of the Council with regard to ecodesign requirements for local space heaters

Model identifier(s): FANCY

Item Symbol Value unit Item unit

Heat output Type of heat input, for electric storage local space

heaters only (select one)

Nominal heat output Pnom 1,40 kW manual heat charge control, with

integrated thermostat

[no]

Minimum heat output

(indicative)

Pmin 1,40 kW manual heat charge control with room

and/or outdoor temperature feedback

[no]

Maximum continuous

heat output

Pmax,c 1,40 kW electronic heat charge control with room

and/or outdoor temperature feedback

[no]

Auxiliary electricity

consumption

fan assisted heat output [no]

At nominal heat output elmax NA kW Type of heat output/room temperature control

(select one)

At minimum heat output elmin NA kW single stage heat output and no room

temperature control

[no]

In standby mode elsb 0,0004 kW Two or more manual stages, no room

temperature control

[no]

with mechanic thermostat room

temperature control

[no]

with electronic room temperature control [no]

electronic room temperature control plus

day timer

[no]

electronic room temperature control plus

week timer

[yes]

Other control options (multiple selections

possible)

room temperature control, with presence

detection

[no]

room temperature control, with open

window detection

[yes]

with distance control option [no]

with adaptive start control [no]

with working time limitation [yes]

with black bulb sensor [no]

Seasonal space heating energy efficiency (portable appliance) ηS(%) 38

Seasonal space heating energy efficiency (fixed appliance) ηS(%) 39

Contact details : ARGOCLIMA SPA - Via A. Varo,35 - Alfianello (BS) - ITALY -

www.argoclima.com

V 05/21

Information for correct disposal of the product in accordance with the European Directive 2012/19/EU

At the end of its working life this equipment must not be disposed of as an household waste. It must be taken to special local

community waste collection centres or to a dealer providing this service. Disposing of electrical and electronic equipment

separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and

enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to

underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.

www.argoclima.com

Argo Fancy Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Argo Fancy

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info