665482
27
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
EG
27
To enter the conguration menu, with Emix already on, press and hold the BUTTON 9 for about 7 seconds.
When only the RED LED lights up, keep BUTTON 9 pressed until the BLUE LED lights up. At this point release BUTTON 9.
After 5 seconds without any operation, Emix exits the conguration procedure and returns to the previous menu.
Booster mode setting
The use of electrical heating elements installed in a storage tank or in a electrical water heater allows you to heat the cold
water faster, to reach the desired water temperature even in conditions of very low external temperatures or to heat the
water even if the heat pump is switched off for maintenance.
When you activate the Booster mode, the software will automatically handle the electrical heaters.
If after 120‘ from start up of the system (the time counter starts when the Booster mode is set), the water setpoint is not
reached, the rst electrical element is automatically activated. The other elements, one by one, will be activated every
120‘ following the course of the water temperature, until reaching the setpoint.
To activate / deactivate the Booster mode, from the conguration menu, quickly press BUTTON 9 until the only BLUE
LED is ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default, the Booster mode is off.
Super Booster mode setting
When the Super Booster mode is activated, all the connected electrical heaters will be activated at the same time, to-
gether with the heat pump.
When the setpoint is reached, all electrical heaters are switched off and the Super Booster mode is automatically turned
off.
To activate / deactivate the Super Booster mode, from the conguration menu, quickly press BUTTON 9 until the only
RED LED is ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default, the Super Booster mode is off.
EMIX CONFIGURATION
Setpoint limit setting with Heat Pump
It is possible to set the maximum achievable setpoint when the Heat Pump is working only for Emix. This limit can be set
to 50°C or 58°C.
To change the setting, from the conguration menu, quickly press BUTTON 9 until the BLUE and YELLOW LEDs are
ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default the limit is set to 50°C. We recommend to keep this setting to preserve the Emix performance.
Antilegionella cycle setting
To activate / deactivate the Antilegionella cycle, from the conguration menu, quickly press BUTTON 9 until the only YEL-
LOW LED is ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default, the Antilegionella cycle is on. It is highly recommended to keep it enabled.
For details on the operation of the Antilegionella cycle, see section “ANTILEGIONELLA CYCLE”.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Argo Emix bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Argo Emix in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds, Fins als bijlage per email.

De handleiding is 4,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Argo Emix

Argo Emix Gebruiksaanwijzing - Deutsch - 29 pagina's

Argo Emix Gebruiksaanwijzing - English - 29 pagina's

Argo Emix Gebruiksaanwijzing - Français - 29 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info