578800
3
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
A microprocessor is at the heart of the amplifier.
It performs several important functions. It switches the amplifier on
or off from standby mode and mutes the two sets of speakers
individually as well as the pre-amp output. It is also responsible for
the remote bus and infra red remote input. Parameters can be
selected, and displayed, on the built in graphic display enabling easy
set up of the amplifier and simple source selection. In addition, the
amplifier uses LED markers to indicate the primary source which is
in use. In addition to a full suite of audio line level inputs, there is
also a high quality optional MM/MC phono stage.To protect your
amplifier, the microprocessor monitors the heatsink temperature
and RF content of the speaker outputs. In the event of the amplifier
being over driven, it can activate the automatic speaker protection
circuits and it can report fault conditions to the main display.
dn
POWER
Switches the unit on and off.The unit can also be switched
into ‘standby’ by use of the remote control handset.
do
POWER INDICATOR
This will initially glow amber. After a few seconds, it will glow
green. When the indicator glows amber, the speakers are
disconnected and an internal protection circuit is activated.
The power indicator will turn red if the unit has been put
into standby mode by use of the remote control.
Under certain conditions the power indicator may flash and
a fault condition will be shown on the display
dp
. If this
happens you should unplug the mains lead of the unit and
leave the unit for a few minutes before re-connecting.
If the fault condition persists unplug and contact your Arcam
dealer.
dk
SP1
Selects or de-selects the main (upper) pair of speakers.
Push the button in to select.
dl
SP2
Selects or de-selects the secondary (lower) pair of speakers.
Push the button in to select.
Important note: If both switches are turned off the amplifier
will appear not to work, as all speakers will be switched off!
cr
VOLUME
Adjusts the volume level of the loudspeakers, pre-amp out
and headphones.The volume can also be controlled with
the Remote Control Handset. As the volume knob is not
motorized the knob will not move when adjusted remotely.
If you spin the knob quickly it will not change the volume.
This is to prevent accidentally setting the volume too high.
NOTE ON VOLUME CONTROL SETTINGS
It is important to realise that the position of the volume
control is not an accurate indication of the power delivered
to your loudspeakers. The amplifier will often deliver its full
power long before the volume control reaches its maximum
position particularly when listening to heavily recorded
compact discs.
However the amplifier also has to be capable of giving full
power output from much lower level sources, such as tuners
and cassette decks. Using these sources, the volume control
setting may be much higher before distortion (audible
overload) sets in.
BALANCE
Press CONTROL
cq
, turn the volume knob to the
desired balance, then press CONTROL again to fix the
balance you have selected.
cq
CONTROL
This button cycles (or steps) through the functions that can
be controlled by the volume knob.This can be either
volume (the default setting) or balance. If you have a
DAVE or MARC, there are several other functions.
Refer to those sections of this handbook.
cs
ENTERTAINMENT (SOURCE) SELECTORS
These buttons select the source (i.e. Radio (TUNER),
Compact Disc (CD) etc. you wish to listen to.
dq
REMOTE RECEIVER
The remote receiver is behind the FMJ badge.
Make sure the remote receiver is not covered or signals
from the Remote Control Handset will not be received.
dm
HEADPHONES SOCKET
Accepts headphones rated between 8 ohms and 2k ohms
fitted with a
1
/
4
stereo jack plug. If you wish to listen on
headphones only, use SPl and SP2 (if necessary) to mute the
speakers.The headphone socket is always active.
Integrated amplifier - User Guide
4
Circled numbers in the text, e.g.
7
, refer to the numbers on the
pictures. If your integrated amplifier HAS NOT been installed for
you, you should read the section entitled ‘Setting up’ before using the
‘User Guide’.
cn cocp cq
dkct dl dm dncscr
dodp
dq
PHONO/AUX
MODE CONFIRM RECORD CONTROL
CD TUNER AV DVD VCR PROCESSOR
2 TAPE 1
SP1 SP2
PHONES
A22 INTEGRATED AMPLIFIER
POWER
VVololumume CDCD
INTRODUCTION
IN USE
5
Integrated amp - Using the Remote Control
Don’t forget to fit the two AAA batteries
supplied and ensure they are inserted
correctly into the back of the remote
control before using it.
The Remote Control sends a message to an
infrared receiver which is located behind the
FMJ badge on the front of the amplifier.
Do not place anything in front of the badge
or the Remote Control may not work.
VOLUME AND (MUTE)
Press ‘+’ to increase volume or ‘–’ to
decrease the output volume of the amplifier.
Press ‘ to mute the speaker connections
and preamp outputs. Both tape outputs and
the headphone socket remain active. Mute is
disabled either by pressing ‘ again, or by
adjusting the volume.
CD CONTROLS
These offer basic controls of Arcam CD
players, such as the FMJ CD23.
DAVE REMOTE CONTROL
If you have a DAVE amplifier, you will have the the CR9000
Remote Control as shown in the DAVE amplifier section
of this handbook.That Remote Control allows you to
operate the integrated amplifier plus some basic functions
of an Arcam or Philips based CD player or Tuner.
TUNER
These buttons are used to control tuner
functions.
Note that the FM/DAB lights indicate into
which mode you are switching the remote
control.The lights only illuminate for five
seconds to conserve battery power.
If neither light is illuminated this does not
mean that the remote control is not
working!
SOURCE SELECTION BUTTONS
These operate in the same way as the
source selectors on the front panel of your
integrated amplifier.
DISP
Cycles through the settings ‘Bright’,‘Off ’ and
‘Dim’.Turning the display ‘Off ’ generally
gives a slight improvement in sound quality.
SP1 AND SP2
These buttons allow you to select and
deselect the main(SP1) and secondary
(SP2) sets of speakers attached to your
amplifier (see page 4).
POWER/STANDBY
Toggles the amplifi er between standby
mode and full power mode.The power
indicator light next to the power button
on the front panel is red if the amplifier
is in standby, amber while the amplifier is
powering up (this only takes a few seconds)
and green when the amplifier is powered up.
If you have an integrated amplifier or MARC amplifier, you will have a Remote Control
similar to the one shown below.
This CR-389 Remote Control gives access to all functions available on the front panel
of FMJ amplifiers. It also has controls to operate Arcam CD players, AM/FM tuners
andDAB tuners.
The Remote Control transmits Philips RC-5 type codes.
OTHER AMPLIFIER FUNCTIONS
Note that greyed-out buttons on the
remote control diagram are of use with
other Arcam amplifiers.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam FMJ P25 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam FMJ P25 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info