482343
63
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
E-61
English
Problem Check that...
Sound only comes from some
of the speakers
<
you have an appropriate surround source selected and playing.
<
the DVD disc is encoded in the appropriate format, and the correct format
has been selected in the disc start menu of the DVD player (if applicable).
<
the DVD player has been set to output ‘bitstream’ audio on the digital
output.
<
the display window indicates that the disc you are playing is a multichannel
recording (you may need to press the INFO key several times until you get to
the ‘incoming format’ display).
<
all the speakers are correctly connected to the speaker terminals and are
secure.
<
you have not selected ‘Stereo’ as the decoding mode.
<
your speaker balance is correct.
<
you have congured the unit to include all the speakers in your system.
Unable to select Dolby Digital
or DTS decoding modes
e AVR500/AVR600/AV888 can only apply Dolby Digital and DTS decoding
to sources which have been encoded in the same format.
Check that:
<
digital source is selected and connected.
<
the source is playing appropriately encoded material.
<
the DVD disc is encoded in the appropriate format and that the correct
format has been selected in the disc start menu of the DVD player (if
applicable).
<
the DVD player has been set to output ‘bitstream’ audio on the digital output
(not PCM).
When playing a Dolby Digital
DVD, the AVR600 selects
Dolby Pro Logic
<
you have a digital connection from your DVD player.
<
sometimes Dolby Digital DVD discs contain material at either the beginning
or the end of the main movie that is not in full 5.1 format, but in two-
channel or Pro Logic decoding.
Hum on the analogue input
<
all cables are making a good connection. If necessary withdraw the cable
from the connector and plug it fully in again (turn the power o before
doing this).
<
the connections inside the source cable connector are not broken or badly
soldered.
<
if the hum originates only when one particular source component is
connected, that an aerial cable, or dish connection to this source is ground
isolated. Contact your installation contractor.
ere is radio or television
reception interference
<
where the interference is coming from. Switch o each source component in
turn, then any other equipment. Most electronic equipment does generate
low levels of interference.
<
try re-arranging cabling from the nuisance source away from other cabling.
<
ensure that the cabling used is high quality, specied for its purpose, and is
properly screened.
<
if the problem persists, contact your dealer.
Problem Check that...
e source switching changes
randomly or freezes on one
source
<
there are no static or impulse interference problems caused by nearby power
equipment switching, e.g., heating or air conditioning control. Switch the
unit o, wait ten seconds, then switch it on again to clear an operating
problem. Contact your installer if the problem returns or persists.
<
there is no direct sunlight shining on the infra-red detector behind the front
panel display.
Volume is always too loud
when I turn on
<
the ‘max on volume setting is not set too high.
When Zone2 or 3 is put into
standby, the main zone is also
switched o
<
the ‘zone standby‘ setting in the setup menu is set to LOCAL.
When a USB memory device is
connected, ‘USB’ is not shown
in the network clients list of
folders
<
a USB memory device is connected that conforms to the mass storage class.
<
a USB hub is not being used.
If les on a USB memory
device cannot be played:
<
the USB device is formatted in FAT16 or FAT32.
<
the USB device does not have multiple partitions.
<
the les are in a compatible format.
If les on a computer cannot
be played
<
the les are in a compatible format.
<
the computer is connected via a network and not USB – the AVR500/
AVR600/AV888 USB port cannot be used for a direct connection to a
computer
If you cannot connect to a
wired network
<
the Ethernet cable you are using is correctly connected between the
AVR500/AVR600/AV888 and the network hardware.
<
the network is set up for xed IP addressing and you have the AVR500/
AVR600/AV888 set to use DHCP.
<
the network is set up for DHCP and you have the AVR500/AVR600/AV888
set to use xed IP addressing.
If you cannot connect to a
favourite internet radio station
<
the station is still broadcasting or is not congested – try again later.
If the internet radio station
sound quality is poor or
broken
<
the radio station does not have a low bit rate (use the INFO key to nd this or
look on the OSD).
<
the network is not slow or congested.
63

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam AV888 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam AV888 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Arcam AV888

Arcam AV888 Gebruiksaanwijzing - Nederlands - 200 pagina's

Arcam AV888 Gebruiksaanwijzing - Nederlands - 72 pagina's

Arcam AV888 Gebruiksaanwijzing - Deutsch, Français - 200 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info