482343
46
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
E-44
Out 1 & 2 Resolution – is setting controls the
output resolution when both HDMI outputs are used
simultaneously. is setting is only valid if Output
Switching is set to Output 1 & 2.
< e dropdown list shows all the resolutions that the
video processor can output. Resolutions that are
not supported by the connected display devices are
greyed out and cannot be selected.
< Best: sets the HDMI output to be the highest
common resolution that is supported by both
display devices.
Out 1 & 2 Frame Rate – is setting controls the
output frame rate when both HDMI outputs are used
simultaneously. is setting is only valid if Output
Switching is set to Output 1 & 2.
< e dropdown list shows all the frame rates that the
video processor can output. Frame rates that are
not supported by the connected display devices at
the above resolution are greyed out and cannot be
selected.
< Auto: sets the HDMI output to be the highest
preferred common frame rate that is supported by
both display devices for the above resolution.
<Follow Input forces the
OUT 1 & 2 frame rate to
the same as the input frame rate, regardless of the
reported capabilities of the display device.
Lipsync 1 & 2 – (Information only) Displays how much
lip sync is automatically applied to HDMI outputs
OUT 1
and OUT 2 simultaneously to compensate for video
processing delays in the attached display devices. Not all
display devices support this function.
Mode
Lists the decode and downmix options you wish to
include when cycling through the options on the MODE
button. Settings are Yes or No. e list is divided into
two sections depending on the source audio type. See
section ‘Multichannel source modes’ on page 47 for
more information on each processing a decoding mode.
ese settings are applied to all audio inputs and are
stored in memory and recalled each time the unit is
powered up.
For Stereo sources:
Dolby ProLogic –
Dolby PLIIx Movie –
Dolby PLIIx Music –
Dolby PLIIx Matrix –
Dolby PLIIx Game
Neo:6 Cinema –
Neo:6 Music –
e rst section, ‘Stereo sources is the list of processing
modes you wish to make available for stereo signals
(analogue stereo, digital PCM stereo, Dolby 2.0, DTS
2.0, etc). When a stereo signal is applied, each press of
the
MODE button cycles through the processing modes
you have enabled in the ‘Stereo sources’ section. e
unprocessed Stereo option is always available for stereo
signals therefore it is not shown in the list.
For Multichannel sources:
Stereo Downmix
Dolby Digital EX
Dolby PLIIx Movie –
Dolby PLIIx Music –
e second section, ‘Multichannel sources’ is the list
of processing modes you wish to make available for
multichannel digital signals (any Dolby or DTS digital
stream that has more channels than stereo 2.0). When a
multichannel digital signal is applied, each press of the
MODE button cycles through the processing modes you
have enabled in the ‘Multichannel sourcessection.
Zone Settings
Lists the volume and control settings for Zone2 and
Zone3 (Zone 3 available with AVR600/AV888 only).
ese settings are applied to all audio inputs and are
stored in memory and recalled each time the unit is
powered up.
Z2 Audio Input – Selects the analogue audio to be
routed to Zone2.
Z2 Video Output – Selects the analogue video to be
routed to Zone2 for the current audio input.
Zone2 Volume – e current volume in Zone2.
Zone2 Max. Vol – Limits the maximum volume setting
the system can be turned up to in the Zone2. is is a
useful feature to prevent accidental overdriving of low
power-handling speakers, for example.
Zone2 Fixed Vol – e Zone2 volume control can be
locked at the current value for use with an external
amplier with its own volume control in Zone2.
Zone2 Max On Vol – Limits the maximum volume the
system operates in the Zone2 when it is switched on
or comes out of Standby. e system comes on at this
volume if the last used (possibly very loud) volume
exceeds this value.
Zone3 Volume – e current volume in Zone3.
Zone3 Max. Vol – Limits the maximum volume setting
the system can be turned up to in the Zone3. is is a
useful feature to prevent accidental overdriving of low
power-handling speakers (for example).
Zone3 Fixed Vol – e Zone3 volume control can be
locked at the current value for use with an external
amplier with its own volume control in Zone3.
Zone3 Max On Vol – Limits the maximum volume the
system operates in the Zone3 when it is switched on
or comes out of Standby. e system comes on at this
volume if the last used (possibly very loud) volume
exceeds this value.
Standby – When a Standby command is received by an
infra-red eye in Zone2, this setting controls which parts
of the AVR500, AVR600 or AV888 to turn on and o:
When Local Only, the Standby IR command only aects
the zone it was received in (Zone2 or Zone3).
When All O, the Standby IR command aects the
entire system in all zones.
Network
e AVR600 and AV888 are tted with a network audio
client (optional for the AVR500) which is capable of
playing internet radio stations as well as stored music
on a network storage device such as a PC, or on a USB
ash drive.
Use DHCP – Select if your network uses DHCP
<No: To assign a xed IP address manually.
<Yes: To use network parameters given by the DHCP
server.
MAC address – (Information only) e unique address
of the network card in your AVR500/AVR600/AV888.
IP Address – If not using DHCP, enter the IP address
you have assigned to the AVR500/AVR600/AV888 for
your network.
Subnet Mask – If not using DHCP, enter the subnet
mask for the AVR500/AVR600/AV888 on your network.
Gateway – If not using DHCP, enter the IP address of
the router the AVR500/AVR600/AV888 is connected to.
Primary DNS – If not using DHCP, enter the Primary
DNS IP address of your internet service provider.
Alternate DNSIf not using DHCP, enter the Secondary
DNS IP address of your internet service provider.
Use Proxy – Select if you connect to the network via a
Proxy Server.
<No: If you connect directly onto the network.
<Yes: If you connect to the network via a Proxy
Server.
Proxy Address – If connecting via a Proxy Server, enter
its IP address.
Proxy Port – If connecting via a Proxy Server, enter the
port number to which the Proxy responds.
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam AV888 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam AV888 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Arcam AV888

Arcam AV888 Gebruiksaanwijzing - Nederlands - 200 pagina's

Arcam AV888 Gebruiksaanwijzing - Nederlands - 72 pagina's

Arcam AV888 Gebruiksaanwijzing - Deutsch, Français - 200 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info