482343
38
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
E-36
It is essential that you enter some information into the
Setup menus about your speaker conguration. is
allows the unit to process any surround sound digital
source to exactly match your system and give you the
ultimate surround sound experience.
ere are three pieces of vital information which are
outlined in the sections: ‘Speaker Types,Speaker
Distances’ and ‘Speaker Levels.
e way you enter this information manually into the
unit is given later in the ‘Setup Menus’ section on page
38. e settings can also be established automatically
using the Arcam Auto Speaker Setup function. However
it is important to understand why these speaker settings
must be entered, which is why this section is presented
rst.
essential
setup
Speaker types
You need to set the type of speakers that you have
connected to your AVR500/AVR600 (or connected
indirectly to your AV888):
Large capable of full frequency range reproduction
Small not capable of full frequency range
reproduction at the low frequency end
None speaker not present in your configuration
e terms ‘Large and ‘Small’ do not necessarily relate to
the physical size of your speakers. As a rule of thumb,
if a speaker cannot reproduce a at frequency response
down to about 40Hz (and very few can!) it is oen better
to consider them as ‘Small’ for setup purposes of home
cinema.
When a speaker is set to ‘Small, very low frequency
sounds are redirected away from that speaker to a ‘Large
speaker or a subwoofer, which are far better suited to
reproducing these low frequency sounds.
Note that it is not possible to set all speakers to
Small’ unless there is a subwoofer in your speaker
conguration. If you do not have a subwoofer, you will
be forced to set your front speakers to ‘Large.
(Advanced users may wish to automatically override the
Small’ speaker setting for purely stereo music listening
when not watching movies. is can be achieved in the
‘Input Cong.’ menu – see page 40.)
Single Surround Back speaker
If you have just one Surround Back speaker in your
conguration instead of two, ensure it is connected to
the SBL speaker connector and set Surr. Back L/R in
the Spkr Types menu to either ‘1 Small’ or ‘1 Largeas
appropriate.
Crossover frequency
If you have set any speakers as being Small, then you will
be required to set a value for the crossover frequency.
is is the frequency below which signals are ltered
away from these Small speakers and redirected to Large
speakers or the subwoofer (if present). A frequency of
80Hz is oen a good starting point, however you will
probably have to experiment with dierent values to nd
the best value for your system or consult your speaker
handbook.
MCH sub level
If a subwoofer is present, this setting allows for a 10dB
compensation on the subwoofer output when using the
MCH input as required by many DVD-A players with
audio outputs.
Use Surround Back channels
If not used in the main zone, it is possible to assign the
Surround Back channels to bi-amp the Front Le/Right
channels or to provide an amplied output to Zone2.
Speaker Distances
It is essential for the distance from each speaker to the
listening position to be accurately measured and entered
into the ‘Setup menu. is ensures that the sounds from
the various speakers arrive at the listening position at
the correct time to recreate a realistic surround eect.
e distance can be entered in centimetres or inches.
Speaker Levels
Finally the levels of all the speakers in the system need
to be adjusted to match each other at the listening
position, again to create a proper surround eect. To
help with this the AVR500, AVR600 or AV888 can
generate a test noise for each speaker which should be
measured with a sound pressure level (SPL) meter. e
meter should be set to ‘C’ weighting and slow response.
e level of noise measured at the listening position
from each speaker should be adjusted on the Speaker
Trims page of the Setup menu so that the meter reads
75dB SPL. It does not matter what the system volume
setting of the AVR500, AVR600 or AV888 is before
turning the test noise on as the volume setting is over-
ridden for the duration of the speaker noise test.
ere are several basic SPL meters on the market at
reasonable prices aimed at home cinema enthusiasts.
Check your local technology store, search online or ask
your dealer.
If you do not have an SPL meter, you can try to adjust
the noise level of each speaker by ear. In this case it is
not possible to adjust the speakers to the absolute 75dB
SPL volume level, but you should aim for all speakers
sounding equally loud. Setting speaker test noise levels
by ear is not recommended as it is very dicult to do
accurately, but is oen better than doing nothing at all!
Before you use your AVR500, AVR600 or AV888 it is
essential that you enter some information about your
system conguration into the Setup menus.
Many of the inputs have several dierent connection
types available, for example, HDMI or component
video; HDMI, digital or analogue audio. It is necessary
to set the connection type used for each input by setting
the Video Source and Audio Source options in the Input
Cong. menu (see page 41). ese options must be set
for each input.
e default for both audio and video sources is HDMI.
If another connection type is used, there will be no
sound or picture from the source until the Video Source
and Audio Source menu items are correctly set.
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Arcam AV888 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Arcam AV888 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Arcam AV888

Arcam AV888 Gebruiksaanwijzing - Nederlands - 200 pagina's

Arcam AV888 Gebruiksaanwijzing - Nederlands - 72 pagina's

Arcam AV888 Gebruiksaanwijzing - Deutsch, Français - 200 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info