15
Assembly
Make sure that the connector is not plugged in.
Hold the two clamps, which hold the upper sec
-
tion in its position and fold them upwards (B2).
Loosen the clamps and lift the upper section up
and out (B3)
.
Turn the tank over so that the upper section is on
the bottom.
Mounting the Rollers
Front Rollers
Insert the two front rollers 14 in the mounts on
the bottom of the container until they snap into
place (B4-A). By pressing on the symbol
for the
roll-away block on the front rollers, unintentional
rolling away of the appliance can be prevented
(B4-B). Release the lock again by pressing on the
symbol
.
Back Rollers
Insert the axle bar 21 into the mount on the side
of the bottom of the container (B5)
.
First of all, push the back rollers 20 on each side.
Then, put the washers 22 on the axle rod and
secure them with the cotter pins 23 (B6)
.
Put the covers 24 on the back rollers 20 (B7).
Insert the foam plastic filter (9) that has been
supplied for wet vacuuming.
(see the section called “Wet Vacuuming“)
Insert the dust bag (10) that has been supplied for
dry vacuuming.
(see the section called “Dry Vacuuming“)
Replace the upper section on the tank (B8).
Hook the clamps into the upper section and let
them snap into place by pressing the clamps
downwards (B9)
.
Place the large end of the hose (4) on the front air
intake stub (17) on the tank (B10).
Select the required nozzle
5 or 7 (B1) or the
stainless steel tubes 6 (B1) and slide them over the
suction tube 4 (B1))
.
Vacuum nozzle (5): for vacuuming carpets,
smooth surfaces and liquids.
In the event of heavy wear, the bottom section of
the vacuum nozzle can be replaced. To do this,
release the lock by putting the two sliders on the
top of the nozzle into position
and then remove
the bottom section. Insert the new bottom sec-
tion and close the lock once again by moving the
two sliders into position
(B11).
Assembly of Drain Extension Hose
Screw the holder for the drain extension hose 26
tightly to the designated opening on the top of
the container (B19) using the screw.
Push the top end of the drain extension hose into
the holder (B21).
Handle (8)
Press on the two securing pins on the outside of
the handle and slide it into the mounts 27 on the
outside of the container until the securing pins
snap into place in the openings designated for
them (B12).
Cable storage
The cable can be coiled on to the rear of the appli
-
ance for storage (B13).
Dry Vacuum Cleaning
ATTENTION! It is absolutely necessary
for you to read, understand, and
observe the section entitled “Safety
Instructions and Warnings”.
NOTE: Never vacuum up hazardous materials.
If an incorrect dust bag is used, then the
guarantee becomes void.
Make sure that the appliance is not plugged into
the power mains.
Make sure that the foam plastic filter (9) (B1) is
clean and dry and installed over the filter basket
(3) (B1)(B14).
Slide the dust bag (10) over the hose connection
(B15) in the tank. Press it until it snaps firmly into
place (B16). In the process, make sure that the
dust bag is not damaged.
Place the upper section on the tank once again
and close the clamps (B8), (B9)
.
Place the large end of the hose on the front air
intake stub (17) on the tank (B10) and screw it in
by turning to the right.
Select the required nozzle
5 or 7 (B1) or the
stainless steel tubes 6 (B1) and slide them over the
suction tube 4 (B1)
.
Make sure that the ON/OFF switch (13) (B1) on the
appliance is in the “Off” position (position “0”) be-
fore you plug the power plug into the receptacle.
Plug the power plug into the receptacle.
Switch the motor on (ON/OFF switch in position
“I”).
When you have finished vacuuming, switch the
motor off by putting the ON/OFF switch (13) (B1)
