807545
9
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
9
6.2.2 CHARGING THE POWER PACK WITH THE MOTOR
VEHICLE CHARGING CABLE
Make sure that the Power Pack is switched o . All control
lights and the work light must not be illuminated. Switch
o the compressor. Plug the coaxial connector of the motor
vehicle charging cable (Position 19 in the overview) into the
charging socket of the Power Pack (Position 9 in the over-
view). Now plug the motor vehicle charging cable into the
12 V on-board socket in your car. The charge status display
(Position 7 in the overview) is activated, and  ashes. If all
three lights on the charge status display are always lit, then
the Power Pack battery is fully charged. After charging,
rst disconnect the motor vehicle charging cable from the
on-board socket, then disconnect the coaxial connector from
the charging socket of the Power Pack.
6.2 CHARGING THE POWER PACK
Fully charge up the Power Pack after purchase with the plug
charger before initial use (Section 6.2.1)
CAUTION
Only charge the Power Pack when driving
or when the motor is running, otherwise
there is a risk that the starter battery of
your vehicle may be discharged.
Make sure that the Power Pack is switched o . All control lights
and the work light must not be illuminated. Switch o the
compressor. Plug the coaxial connector of the plug charger
(Position 18 in the overview) into the charging socket of
the Power Pack (Position 9 in the overview). Now, connect
the plug charger with the mains socket. The charge status
display (Position 7 in the overview) is activated, and  ashes.
If all three lights on the charge status display are always lit,
then the Power Pack battery is fully charged. After charging,
rst disconnect the plug charger from the mains socket, then
disconnect the coaxial connector from the charging socket of
the Power Pack.
6.2.1 CHARGING THE POWER PACK: WITH THE PLUG
CHARGER
6.3 STARTING AID
For instructions on carrying out a jump
start, read the manual of your vehicle or
ask your specialist workshop.
Disconnect all of the devices connected to the Power Pack
from the 12 V outlet socket (Position 6 in the overview) and
from the USB port (Position 11 in the overview).
Make sure that the Power Pack is fully charged. To do this,
press the ON/OFF switch (Position 8 in the overview). If all
three lights are illuminated on the charge status display
(Position 7 in the overview) then the Power Pack is ready to
use.
6. OPERATING INSTRUCTIONS
6.1 OVERVIEW
Figure 1: Overview
1 Handle
2 Control panel front
3 LED indicator  eld
4 Jump lead (+)
5 Jump lead (-)
6 12 V outlete
7 Charge status display
8 Switch
9 Charging socket
10 USB control light
11 USB port
12 Compressor switch
13 Manometer
14 Rear side of control panel
15 Pole calliper (-)
16 Air hose storage
compartment
17 Pole calliper (+)
18 Plug charger
19 Motor vehicle charging cable
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Apa 16553 - TMSPL-28 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Apa 16553 - TMSPL-28 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0.74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info