Handleiding Angelcare AC401de luxe (pagina 6 van 16) (Engels)

537057

Verklein

Vergroot

Pagina terug

1/16

Pagina verder

Step 5: Changing Channels

The Angelcare Monitor has 8 manually

selectable channels. If the transmission is

not clear or you experience interference the

channel can be changed as follows:

1. Turn both units ON.

2. Press and hold the SELECT button.

3. The current channel will be shown on the

Parent Unit display.

4. Change the channel with the ARROWS UP

or DOWN.

5. Press the SELECT button again to conﬁrm

the channel.

ALWAYS keep at least 3 metres distance

between the Parent Unit and the Nursery

Unit to avoid feedback (loud whistling

noise) between the units.

Step 6: Testing your Monitor

1. TEST YOUR MONITOR TO DETECT

MOVEMENT

1a. Make sure the Sensor Pad is installed

correctly and turn both units ON.

1b. Gently move your hand over the mattress

to simulate your baby’s movements.

Note: The movement alarm will sound if no

movement is detected within 20 seconds.

1c. Once movement is detected the green

PENDULUM light will ﬂash on the Nursery

Unit and the PENDULUM icon on the

Parent Unit screen will swing.

1d. After approx. 1 minute remove your hand

from the mattress. Do not lean against

the baby’s bed!

2. STOPPING THE ALARM

There are 2 ways of stopping the alarm once

it is sounding:

a. Turn off the nursery unit

b. Press any key on the parent unit (except

the ON OFF button). This will put the

monitor on HOLD. To deactivate the HOLD

function press and hold the down arrow

for 2 seconds. (See Other Functions

Section).

3. THE 4 CORNER TEST

Follow the same process for all 4 corners of

the mattress to ensure that the SensorPad is

picking up movements from all corners of the

mattress. If the monitor does not alarm after

20 seconds once you have taken you hand off

the mattress, the SensorPad may be detecting

other movements such as a cot mobile, a fan,

or simply the cot being touched or leant on.

If the monitor does alarm during this testing,

this could indicate that the sensitivity of the

sensor pad may need adjusting. (See

Adjusting the Sensitivity Setting).

Step 7: Adjusting the Sensitivity Settings

The Standard Setting for the Sensitivity is

Level 3. (The Sensitivity Dial on the back

of the Nursery Unit will be pre-set to Level

3. This is suitable for most bed sizes and

types of mattress. Do not Adjust unless

necessary. By increasing the sensitivity

the Sensor Pad will cover a larger area. It

could also detect vibrations from outside the

baby’s bed (i.e. cot mobiles or fans), or other

movements. It is important to ﬁnd the right

balance for your situation, to ensure optimum

performance of the sensor pad. Reducing

the sensitivity can be useful if the sensor

pad is picking up external movements. For

example a cot placed right next to an adults

bed could be picking up the movements from

the adults. In this instance you may need to

reduce the sensitivity. We recommend only

moving the Sensitivity Adjustment Dial by half

a notch and repeating the ‘4 Corner Test’, as

described above. Try this new setting for a

few days. If you need to further increase or

decrease the sensitivity please do this by a

further ½ notch and re-test.

Step 4: Establishing connection between the Parent Unit and the Nursery Unit

Once you have completed Steps 1, 2 & 3, turn

your Parent Unit on by pressing and holding

the Power button. Turn the Nursery Unit on by

pushing up the left wing to the ON position.

You will see the Channel Number appear and

after a few seconds this will change to the

temperature reading of the baby’s room.

AC401 DELUXE

1. Install the baby monitor according to the

instructions with one of the Parent Units.

This Parent Unit and Nursery Unit should

connect automatically. If this is not the

case, please follow the reconnecting

procedure. Your baby monitor is now ready

for use with one Parent Unit. If you want to

connect the 2nd Parent Unit, please go to

Step 2.

2. Keep the ﬁrst Parent Unit and Nursery Unit

turned ON and then turn on the 2nd Parent

Unit, which should also connect

automatically. If this is not the case, please

follow the reconnecting procedure. Once

both Parent Units are connected to the

Nursery Unit your baby monitor is ready

for use.

3. All monitor settings can be changed from

both Parent Units (according to the

Instruction Manual). The new settings will

automatically be activated on both

Parent Units.

SWITCHING ON

The connection between the Parent and

Nursery Unit is automatically established

every time both units are ON.

RECONNECTION PROCEDURE

Should connection not be automatically

established when you turn on both units

please follow the reconnection procedure on

the right:

1. Turn both units OFF.

2. Turn ON the Parent Unit, then press and

hold the MENU button until a beep

sounds and the OUT OF RANGE indicator

starts ﬂashing.

3. Turn ON the Nursery Unit, then press and

hold the PAIRING button on the front of

the Nursery Unit until a beep sounds and

the TIC light ﬂashes (see PART 1, Step

1a).

4. The Parent Unit will show the channel

number, which will be replaced by the

standard menu after a few seconds.

NOTE

If the Parent Unit is turned ON but the

Nursery Unit is OFF, the Parent Unit will

double beep for 1 minute and then turn

itself off as it cannot locate the Nursery

Unit. By turning the Nursery Unit on again

this will re-establish connection and the

monitor is ready for use.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Angelcare AC401de luxe Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Angelcare AC401de luxe

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info