537058
6
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
6
Warnings
This product is NOT a medical device nor a device to prevent cases of
Sudden Infant Death Syndrome (SIDS).
This product is NOT a substitute for direct supervision of your baby.
Check your baby’s activities at regular intervals. Monitoring of
premature babies, or those considered to be at risk, should be carried
out only under the supervision of a doctor or health professional.
Please make sure you DON'T put the Parent Unit near wireless devises
and microwave ovens. This may disrupt the transmission of the alarm
signal.
The Sensor Pad may detect movement from many sources from both
inside and outside your baby’s room, for example: fans, washing
machines, loud music, etc.
Ensure that all vibration sources are
eliminated before using the Angelcare
®
Monitor. Avoid contact
with crib when monitor is in use. Refer to the Movement
Sensitivity Adjustment and Troubleshooting section.
ALWAYS place both units on flat surface in an upright position, away
from baby’s reach.
DO NOT touch the end of the adapter cord when plugged into an
electrical outlet.
The Angelcare
®
Monitor uses public airwaves to transmit signals. The
Parents Unit may pick up signals or interference from other nursery
monitors in your area. Your monitor may even be picked up by other
households. To protect your privacy, make sure both units are in the
OFF position when not in use.
This product should be serviced by qualified personnel. There are no
user serviceable parts inside monitor. Refer all service questions to
your distributor (see page 71).
Instructions
RETAIN INSTRUCTIONS: Keep user’s manual for future reference.
WATER, MOISTURE AND HEAT DAMAGE: Keep all components away
from water (sink, bath tub, swimming pool) and places that emit heat
(stove, radiator).
VENTILATION: ALWAYS place both units on flat surface in an upright
position so that air can flow freely around them.
AC POWER SOURCE: Use only the AC adapters supplied with the
Angelcare
®
Monitor.
CORD PROTECTION: Avoid damage to the cords of the Sensor Pad and
adapters. Route cords so that they are not likely to be walked on or
pinched by items placed upon or against them.
CLEANING: Disconnect all units before cleaning. DO NOT immerse in
water. Use a dry cloth to keep monitor free from dust. DO NOT spray with
cleaning products or solvents. Wipe Sensor Pad with a very slightly
damp cloth with an antiseptic or mild detergent.
OBJECT AND LIQUID ENTRY: Care should be taken so that objects do
not fall onto units and that liquids are not spilled into either unit or
Sensor P
ad through its openings.
NON-USE PERIODS: When not using monitor for long periods, remove
the batteries from both units and disconnect the AC adapters from
electrical outlet.
Testing Your Angelcare
®
Monitor
Note: Test your Angelcare
®
Monitor BEFORE first-time use and then
on a periodic basis.
The
Angelcare
®
Monitor can be used outside of the crib,
in a different
sleeping area. Test monitor when moving Sensor Pad to a new location
to ensure sensitivity is adjusted correctly to the new padding or
ma
ttress. Consult the Movement Sensitivity Adjustment section.
Step 1. On the Nursery Unit, switch to the “Sound Only” function.
Have someone else speak into the Nursery Unit or place a radio near
Nurser
y Unit. You should hear sound from the Parents Unit. If there is no
sound, refer to the Troubleshooting section.
Make sure that both units are
on the same channel, either on A, B or C. If reception is not clear,
switch to other channel.
Step 2. Test monitor to detect movement. Switch Nursery Unit to the
“Movement” function. Gently move your hand on the mattress. The
green light will continue to flash with your every movement. Remove
hand from mattress. Due to no movement, a “pre-alarm Tic” sound will
emit after 15 seconds. 5 seconds later, the alarm will sound and the red
light will flash continuously.
NOTE: If alarm does not sound,the Sensor Pad may be detecting a continuous
vibration from the floor, a strong draft or the crib is being touched. Avoid
contact with crib when monitor is in use. Place crib near a solid supporting
wall and away from strong air currents.The sensitivity of the Sensor Pad may
need to be reduced, consult the Movement Sensitivity Adjustment section.
Step 3. To stop alarm, place your hand lightly on mattress for Sensor
Pad to redetect movement. The red Alarm indicator light on the Nursery
Unit will continue to flash 1 minute (Figure 3).
Step 4. Verify that the battery mode is functional by operating both units
without the AC adapters.The green Power light should appear on both units.
Parents Unit: When orange Low Battery indicator light appears, replace
batteries promptly for Model AC301. For Model AC301-R, recharge
Parents Unit for 12 hours.
Nursery Unit: When orange Low Battery indicator light appears a rapid
“clicking” is heard, the temperature indicator turns off and a beep will
sound every 30 seconds, replace batteries promptly. If not, the light will
eventually turn red and the monitor will stop working.
Operating Tips
Movement Sensitivity Adjustment
The Sensitivity Adjustment Dial has been preset to suit
most situations. However in certain circumstances,
the sensitivity may not be ideal.
DO NOT increase sensitivity unless false
alarms occurs and you have followed the advice in the Troubleshooting
section for false alarms. Make a note of the pre-set position of the dial
should you wish to return to it.
The Alarm Indicator Light on the Nursery Unit will flash red and beep
once when monitor barely detects movement. This could be a result of:
baby being in a very deep sleep or baby having moved away from
Sensor Pad to edge of crib. If alarm does
NOT sound, no adjustment of
sensitivity is required. If the alarm indicator light flashes red most of the
time with baby directly over the location of either Sensor Pad, a false
alarm may occur. If this happens, adjust the sensitivity.
To adjust sensitivity, increase dial to the next setting. Retest monitor.
Channel selection for sound reception
Make sure that both units are on the same channel, either on A, B or
C. If reception is not clear, switch to another channel.
If interference
persists, consult the Troubleshooting section.
Green Sound Lights
The three Sound Lights allow you to see baby’s sounds. The louder the
sounds from baby, the more lights appear.
Temperature display
The Nursery Unit is equipped with room temperature display. The
temperature is displayed in Celsius (C).
Night light halo
Press on the first light at the top of the Nursery Unit to activate the night light.
Voice activated
This monitor is equipped with a voice activa
ted system.
The nurser
y unit will
be activa
ted and transmit sounds to the parents unit only when it ca
ptures
sound.
This will make sure tha
t the parents unit will only respond to its
ma
tching nurser
y unit.
Digital coding system
This monitor is equipped with a digital coding system which eliminates
interferences. The codes are written on the box and in the battery
compartment. For use of 2 Angelcare Movement and Sound Monitor in same
0
1
23
4
5
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Angelcare AC301 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Angelcare AC301 in de taal/talen: Nederlands, Duits, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Angelcare AC301

Angelcare AC301 Gebruiksaanwijzing - English, Français - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info