541764
9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
SVT-3 PRO Bass Guitar Amplifier SVT-3 PRO Bass Guitar Amplifier
9
The Rear Panel continued
28
CAUTION:
TO
REDUCE THE RISK
OF FIRE, REPLACE
FUSE WITH SAME
TYPE AND RATING.
SPEAKER OUTPUTS
AC LINE IN
ATTENTION:
UTILISER UN FUS-
IBLE DE RECHANGE
DE MEME TYPE.
110/115V: 250V T10A SLO BLO
230V: 250V T5A SLO BLO
MODEL:
SERIAL:
LINE: V ~ Hz
WATTS: MAX
SVT-3PRO
120 XX
1000
CAUTION
RISK OF ELECTRIC
SHOCK - DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE
NE PAS OUVRIR
TO REDUCE THE RISK
OF FIRE OR ELECTRIC
SHOCK, DO N OT EX-
POSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
AVIS:
275 WATTS @ 8 OHMS
450 WATTS @ 4 OHMS
4 OHM MIN. LOAD
EFFECTS LOOP
TUO RENUTLEVEL
RETURN SENDPOWER AMP
IN
PREAMP
OUT
FOOTSWITCH
PRE
PULL
GROUND
LIFT
POST
29 30 31 32 33 34 35
3222 2726252421
BALANCED
TRANSFORMER BAL. LINE OUTPUT
BALANCED/
UNBALANCED
29. IEC POWER INPUT CONNECTOR: This
is where you connect the supplied AC
power cord.
DO NOT DEFEAT THE GROUND PRONG
OF THE AC PLUG!
30. SPEAKER OUTPUTS: These mono 1/4"
TS output jacks supply speaker-level
power to the speaker cabinet. The rated
power output is 275 watts rms into 8
ohms or 450 watts rms into 4 ohms.
The two identical outputs are wired in
parallel, and you can use either one, or
use both. Make sure the total speaker
impedance load is 4 ohms or greater.
For example, you could connect:
Two 16 ohm speakers (an 8 ohm load),
Two 8 ohm speakers (a 4 ohm load)
or one 4 ohm speaker.
Use speaker cables with 1/4" TS ends
to make the connections. Do not use
instrument cables as they may overheat.
We recommend using the Speakon
jack [22] whenever playing at full
output levels.
31. POWER AMP IN: This jack connects
directly to the internal power amp for
use with an external preamp. When
using an external source, connect the
OUTPUT of the source to this jack using
a shielded instrument cable to feed the
signal into the power amp section. The
internal signal is disconnected when a
plug is inserted into this jack.
32. PREAMP OUT: This jack is a direct
post master preamp output for use with
an external power amp. Connect the
external amp’s input to this jack using a
shielded instrument cable.
33. EFFECTS LOOP RETURN: When using
an external signal processor, connect
the OUTPUT of the effect to this jack
using a shielded instrument cable to
feed the processed signal into the unit.
34. EFFECTS LOOP SEND: When using
an external signal processor, connect
the INPUT of the effect to this jack
using a shielded instrument cable to
send the post-EQ signal to the effect
for processing.
35. FOOTSWITCH: Connect a dual
footswitch to this jack for remote Mute
and EQ On/Off control. On the stereo
1/4" plug, the tip controls Mute and
the ring controls EQ On/Off. The EQ
footswitch overrides the front panel
switch and the Mute function is
available from either location.
NOTE:
A footswitch may be purchased at
your local Ampeg Dealer or ordered directly
from LOUD Technologies Inc. Be sure to ask
for model #AFP2.
OTHER: Make sure that the ventilation
openings are not obscured in any way. This
will allow the flow of cooling air to the power
amplifier’s heatsinks.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ampeg SVT-3 Pro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ampeg SVT-3 Pro in de taal/talen: Engels als bijlage per email.

De handleiding is 1,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info