644612
26
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
26
User’s manual
EN
Problem Cause Remedy
The ashing of the LEDs
signals a “wheel motor
error” LED ashes.
(1 FLASH of the green ON/
OFF led - Right motor error).
(2 FLASHES of the green
ON/OFF led - Left motor
error)
Uneven ground or ground with
obstacles that impede movement.
Check that the lawn to mow is even and does
not have any holes, stones or other obstacles.
If so, ll in any holes and remove any obstacles
(see “Preparation and dening the boundaries of
the work areas”).
One or both wheel motors has a fault.
Have the motor repaired or replaced by the
nearest authorised service centre.
PLAY
ON
PAUSE
STOP
H
I
G
H
B
A
T
T
E
R
Y
L
O
W
B
A
T
T
E
R
Y
OFF
The ashing of the LEDs
signals a “motor/blade
error”.
(3 consecutive FLASHES of
the green ON/OFF led).
Cutting blade damaged.
Replace the blade with a new one (see “Blade
Replacement”).
Cutting blade fouled (tape, ropes,
plastic fragments, etc.).
Stop the robot safely (see “Robot Safety Stop”).
Warning – Caution
Use protective gloves to avoid the risk of
injury.
Remove the cause of fouling of the blade.
The robot was started too close to
obstacles (less than 1 m. (40.00 ")
away) or in the presence of unexpected
obstacles (fallen branches, forgotten
objects, etc.).
Stop the robot safely (see “Robot safety stop”).
PLAY
ON
PAUSE
STOP
H
I
G
H
B
A
T
T
E
R
Y
L
O
W
B
A
T
T
E
R
Y
OFF
Remove the obstacles and restart the robot.
Electric motor failure.
Have the motor repaired or replaced by the
nearest authorised service centre.
Too high grass.
Increase the cutting height (see “Cutting height
adjustment”).
Carry out a preliminary cutting of the area with a
normal lawnmower.
The ashing of the LEDs
signals a “tip-over error”.
(4 consecutive FLASHES of
the green ON/OFF led).
Ground with too much slope or with
undened borders.
Check the installation rules.
Tip-over sensor failure.
Try to restart the robot. If the problem persists,
have the robot repaired by the nearest
authorised service centre.
PLAY
ON
PAUSE
STOP
H
I
G
H
B
A
T
T
E
R
Y
L
O
W
B
A
T
T
E
R
Y
OFF
The ashing of the LEDs
signals a “curb drop-off
sensor error”.
(Led (ON/OFF) 5
consecutive ashes).
When the robot is started it does not
detect the curb drop-off sensor data
correctly.
Clean the sensors and start the robot again. If
the problem continues, decide whether to start
the robot with the curb drop-off sensors off,
otherwise contact the Authorised Service Centre
closest to you.
PLAY
ON
PAUSE
STOP
H
I
G
H
B
A
T
T
E
R
Y
L
O
W
B
A
T
T
E
R
Y
OFF
The power supply unit does
not turn on.
No electricity.
Check that the power supply unit is correctly
connected to the power outlet.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ambrogio-L50

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ambrogio L50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ambrogio L50 in de taal/talen: Engels als bijlage per email.

De handleiding is 9,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ambrogio L50

Ambrogio L50 Aanvulling / aanpassing - Nederlands - 3 pagina's

Ambrogio L50 Aanvulling / aanpassing - Nederlands - 2 pagina's

Ambrogio L50 Gebruiksaanwijzing - Nederlands - 44 pagina's

Ambrogio L50 Gebruiksaanwijzing - Deutsch - 23 pagina's

Ambrogio L50 Gebruiksaanwijzing - Deutsch - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info