733759
30
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
28
User’s manual
EN
INITIAL START UP – AUTOMATIC MODE
The automatic cycle is started during the initial start-up or after a period of inactivity.
1. Check that the height of the lawn surface to mow is compatible with the proper functioning of the robot (see “Technical
Specications”).
2. Adjust the cutting height as desired (see “Adjustment of Cutting Height).
3. Check that the work area has been correctly marked and that there are no impediments to the regular functioning of the robot
as indicated in the section “Preparation and Marking the Boundaries of the Work Areas” and following sections.
4. Position the robot inside the charging station.
5. Press the "ON/OFF" button and wait a few seconds for the robot to turn on completely. Follow the instructions on the display
and enter the password if prompted.
6. If starting the robot for the rst time, it is necessary to program the settings. However, if starting the robot after a long period
of inactivity, check that the programmed functions correspond to the actual condition of the lawn to be mowed (e.g. addition
of a pool, plants, etc.) (See “Programming Mode”).
7. After a few seconds, the message “CHARGING” will appear on the display.
8. The robot starts to mow the lawn according to the modes programmed.
9. Check there are no large puddles after a heavy rain, otherwise the area must be put in order or make sure the robot is in
"Pause".
ROBOT SAFETY STOP
During use, it may be necessary to stop the robot. In normal conditions, the robot can be stopped with the “STOP” key. In case
of danger or when performing any maintenance, it is necessary to stop the robot in safe conditions in order to prevent the blade
from accidently starting. First press the “STOP” button and then the "ON/OFF " button. Disconnect the power plug from the
electrical outlet.
Important
The robot safety stop is necessary during
maintenance and repairs (for example, blade
replacement, cleaning operations, etc.).
To start, proceed as indicated:
-
position the robot inside the cutting area;
-
press the "ON/OFF" button to turn on the robot and run the
start-up procedure again.
If the robot is started up outside of the cutting area, the blade
motor will not start and after briey searching for the signal, the
robot will show "OUT OF BORDER" on the display. Press "ON/
OFF", position the robot inside the cutting area and carry out the
start up procedure again.
ON/OFF
STOP
.....................................
......................
10:30
AUTOMATIC RETURN TO THE CHARGING STATION
The robot stops the work cycle if the following conditions are veried:
-
End of working time: at the end of the working time, the robot automatically returns to the charging station and starts
operating again according to what has been programmed (see “Programming Mode”).
-
Rain: with the function active, the robot returns to the recharging station automatically and will start working again as
programmed (see "Programming mode").
-
Battery to be charged: the robot automatically returns to the charging station.
-
Eco Mode: if the sensor detects that the lawn has already been mowed, it automatically returns to the charging station and
starts operating again according to what has been programmed (see “Programming Mode”).
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ambrogio L250i Elite bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ambrogio L250i Elite in de taal/talen: Engels als bijlage per email.

De handleiding is 8,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Ambrogio L250i Elite

Ambrogio L250i Elite Gebruiksaanwijzing - Nederlands - 42 pagina's

Ambrogio L250i Elite Gebruiksaanwijzing - Deutsch - 42 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info