733759
13
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
11
User’s manual
EN
SETTING UP OF THE PERIMETER WIRE
Before installing the perimeter wire, it is necessary to check the
entire surface of the lawn. Make any necessary adjustments to the
grassy surface during the laying of the perimeter wire in order to
allow the robot to function correctly.
1. Evaluate the best method for returning to the charging station
according to the instructions described in the chapter “RE-
ENTRY METHOD TO THE CHARGING STATION”.
2. Evaluate whether a special installation of the perimeter wire
is necessary according to the instructions described in the
chapter “SET-UP OF THE ROBOT’S QUICK RE-ENTRY TO
THE CHARGING STATION”.
3. Preparation and dening of the work areas.
4. Installation of the perimeter wire.
5. Installation of the charging station and power supply unit. When
laying the perimeter wire, respect the installation direction
(clockwise) and the rotation direction around the owerbeds
(counter-clockwise), As shown in the gure.
track for laying the perimeter wire
RE-ENTRY METHOD TO THE CHARGING STATION
The robot can return to the charging station in two different ways
based on what is set in the user menu under the eld “Settings
Re-entry to Base.” Use the “On the Wire” method only when there
are numerous obstacles inside the garden and near the perimeter
wire (within 2 meters). In all other cases it is better to use the
“V-Meter” method for the quickest re-entry to the charging station.
“Follow wire”. This method of re-entry to the charging station
commands the robot to follow the perimeter wire, positioning its
wheels on either side of the wire. If this method is activated, there
is no need to prepare the “Recall on Wire” as described below.
“V-Meter”. By setting this method of re-entry to the charging
station, the robot runs along the perimeter wire at an indicative
distance ranging from a few centimetres to one meter (3.2 '),
touching it every now and again in the curved sections until the
signal emitted by the charging station has been recognised for
guiding itself on the wire and entering correctly into the charging
station.
step
lower 2 mt.
5 cm.
2 mt.
2 mt.
2 mt.
10 mt. 1,5 mt.
charging
station
If narrow passages are present or the arrow for quick re-entry to the charging station, the wire must be positioned in a special
way, called “Recall on the wire.”
As soon as a “Recall” is recognised, the robot will follow the perimeter wire at low speed, and with more precision for around
10 meters (33 '). It will then return to the “V-Meter” re-entry mode if the quick re-entry or charging station was not encountered.
Follow these instructions to install the “Recall”:
the “Recall” is a piece of wire that extends for around 2 m (6.6 ') with a distance of 5 cm (1.96 ") between each wire;
the “Recall” must be positioned at a distance of 2 m. (6.6 ') in front of any narrow passages;
the “Recall” must be positioned in the section in front of the “Quick Re-entry”.
NB: If the robot does not nd the charging station within a certain amount of time, it will follow the perimeter wire in
“Follow wire” mode.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ambrogio L250i Elite bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ambrogio L250i Elite in de taal/talen: Engels als bijlage per email.

De handleiding is 8,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ambrogio L250i Elite

Ambrogio L250i Elite Gebruiksaanwijzing - Nederlands - 42 pagina's

Ambrogio L250i Elite Gebruiksaanwijzing - Deutsch - 42 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info