471407
44
Verklein
Vergroot
Pagina terug
1/67
Pagina verder
42-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
Before Performing Automatic
Measurement
This unit is equipped with ImprintEQ, RoadEQ, and AutoTCR as
automatic measurement functions.
The Commander cannot set ImprintEQ setup. Refer to PC Operation
Section “Setting ImprintEQ” (page 17).
Be sure to read before performing the automatic
measurement.
The automatic measurement should be performed in a quiet place
with the engine, air-conditioner, and heater turned off. If a mobile
phone or car phone is installed in the vehicle, move them outside of
the cabin, or turn the power off. Sound other than the measuring
sound (ambient noise around the vehicle, engine noise, and
ringtones) may interfere with measurement, resulting in inaccurate
measurement of the acoustic characteristics of the cabin.
Be aware that the battery may be drained if you use the unit for an
extended period of time without running the engine.
The microphone supplied with this product is specifically designed
for this type of measurement. Use of any other microphone will give
poor or no results. Use of microphones other than the one supplied is
not recommended.
If the system is equipped with a power amplifier with input level
control or a powered subwoofer, the measurement may not be
possible if the input level is set low. However, to perform correct
measurement, the input level should not be set too high.
For a power amplifier with low-pass filter, turn off the low-pass filter
of the power amplifier to make measurement. The low-pass filter in
the powered subwoofer or the power amplifier for a subwoofer
should be set at the highest cutoff frequency.
Measurement sequence for the automatic measurement
functions
Perform the automatic measurement in the following sequence.
When ImprintEQ is used:
First, ImprintEQ, then RoadEQ.
When ImprintEQ is not used:
First, AutoTCR, then RoadEQ.
When ImprintEQ is used, AutoTCR is not required.
When ImprintEQ and AutoTCR are performed after RoadEQ, re-
perform RoadEQ.
Turning ImprintEQ On/Off
ImprintEQ setting is performed on a PC. The commander can only
switch the ImprintEQ memory settings.
1
Press and hold [FUNC.] for at least 2 seconds.
The memory setting switches with each press.
ImprintEQ 1 ImprintEQ 2 ImprintEQ OFF
ImprintEQ 1
ImprintEQ 1/ImprintEQ 2: ImprintEQ ON mode
Memory settings that do not include ImprintEQ measurement data
are skipped.
For further details on ImprintEQ, refer to PC Operation Section
“Setting ImprintEQ” (page 17).
Adjusting the Time Correction
Automatically (Auto TCR)
A vehicle poses a unique listening environment. Speaker distances vary
widely to each listening position. These special conditions can be
overcome using the included microphone and the powerful
measurement system in this processor. The processor measures and
analyzes data automatically to optimize time correction for each speaker
and listening position selected.
1
Preparing for measurement.
Park the vehicle in a quiet location.
Close doors, windows, sunroof, etc.
Turn the air-conditioner and heater OFF.
Turn off the engine of the vehicle.
2
Preparing the microphone.
Place the microphone at the listening position (driver’s seat,
etc.). A camera tripod is recommended for this purpose.
The microphone should be placed at shoulder height.
When you save the measurement data values for various listening
positions in the preset, you can easily load one of them as necessary.
3
Turn the ignition switch of the vehicle to ACC (On).
If an air-conditioner or heater is turned on, turn it off. Measurement
should not be performed if air-conditioner or heater noise is present.
4
Press [FUNC.].
5
Rotate the [Rotary encoder] to select “Sound Field
Adj.,” and then press the [Rotary encoder].
Automatic
Measurement
Function
WARNING
Do not perform automatic measurement while the vehicle is
running.
Do not perform automatic measurement while the vehicle is
running. Automatic measurement requires microphones to be
installed in the cabin to measure acoustic characteristics, and
the speakers may output loud noise for measurement. This
may interfere with safe driving and lead to an accident.
FUNC.
Rotary encoder
01GB00PXAH800.book Page 42 Tuesday, February 8, 2011 9:04 PM
44

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alpine RUX-C800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alpine RUX-C800 in de taal/talen: Engels als bijlage per email.

De handleiding is 11,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info