Handleiding Alpina T 26 J (pagina 16 van 27) (Alle talen)

731918

Verklein

Vergroot

Pagina terug

1/27

Pagina verder

condition and in particular:

– The throttle trigger and the safety lever must

move freely, they must not need forcing and

should return automatically and rapidly back

to the neutral position;

– The throttle trigger must remain locked until

the safety lever is pressed;

– The engine stop switch must easily move from

one position to the other;

– The electric cables and in particular the spark

plug cable must be in perfect condition to

avoid the generation of any sparks, and the

cap must be correctly tted on the spark plug;

– The machine handgrips and protection devic-

es must be clean and dry and well fastened to

the machine;

– Check the correct position of the handgrips

and the connection point of the harness, and

the proper balance of the machine.

– Make sure that the guards are suitable for the

cutting means being used and are tted cor-

rectly.

– There must be no signs of damage on the

cutting means. Make sure the cutting means

is not worn or damaged. Replace the dam-

aged or worn cutting means to preserve bal-

ance. Any repairs must be done at a special-

ised centre.

4) WARNING: DANGER! Petrol is highly

flammable.

– Keep the fuel in containers which have been

specically manufactured and homologated

for such use;

– add fuel, using a funnel, only outdoors; do not

smoke during this operation and each time fu-

el is handled;

– Slowly open the fuel tank to allow the pressure

inside to decrease gradually;

– Add fuel before starting the engine. Never re-

move the tank cap or add fuel while the engine

is running or when the engine is hot;

– if you have spilled some fuel, do not attempt to

ignite the engine but move the machine away

from the area of spillage and avoid creating

any source of ignition until the fuel has evapo-

rated and fuel vapours have dissipated:

– Always put the tank and fuel container caps

back on and tighten well;

– Immediately clean up all traces of fuel spilt on

the machine or on the ground;

– Never start the machine in the same place you

relled it with fuel; the engine must be started

in an area at least 3 metres from where you re-

lled the fuel tank;

– Make sure your clothing does not come into

contact with the fuel, on the contrary, change

your clothes before starting the engine.

5) Replace faulty or damaged silencers.

C) DURING USE

1) Do not operate the engine in a conned space

where dangerous carbon monoxide fumes can

develop.

2) Work only in daylight or with good articial

light in good visibility conditions. Keep per-

sons, children and animals away from the work-

ing area.

3) Always use caution and take on a rm and

well-balanced position

4) Where possible, avoid working on wet, slip-

pery ground or in any case on uneven or steep

ground that does not guarantee stability for the

operator;

5) Make sure you have a steady foothold on

slopes.

6) Never run, always walk.

7) Pay particular attention to uneven ground or

the presence of obstacles.

8) Always work across the face of the slope

and never up and down it, being very careful

when changing direction, making sure the cut-

ting means is always downstream.

9) Do not use the machine if you are unable to

hold it with both hands or keep it steady on your

legs while working.

10) The machine must never be used by more

than one person.

11) When working, the machine must always be

rmly held in both hands, keeping the power unit

on the right of the body and the cutting-means

assembly below the line of the belt.

14) Pay attention to trac when using the ma-

chine near roads.

13) Never use the machine with damaged or

missing guards.

14) Always keep hands and feet away from the

cutting means, when starting and when using

the machine.

15) Beware of injuries caused by devices used

to cut the line length. After releasing the new line,

always put the machine in a working position be-

fore starting the engine.

16) Be careful of ying debris coming from the

cutting means.

17) Warning: the cutting means continues to ro-

tate even after the engine has been switched o.

18) Make sure the machine is securely locked

when you start the engine:

– Check that there is nobody within at least 15

metres of the machine’s range of action or at

least 30 metres for heavier cutting;

– Do not direct the silencer and therefore the ex-

haust fumes towards inammable materials.

19) Do not change the engine settings or over-

speed the engine.

20) Do not strain the machine too much and do

not use a small machine for heavy-duty works.

If you use the right machine, you will reduce the

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Alpina T 26 J Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info