731905
14
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
USING THE MACHINE / MAINTENANCE AND STORAGE 9
EN
WARNING! For your safety and that of
others:
After each use, disconnect the machine
from the mains and check for damage.
Correct maintenance is essential to main-
tain the original eciency and safety of the
machine over time.
Keep all nuts, bolts and screws tight to be
sure the equipment is in safe working con-
dition.
Never use the machine with worn or dam-
aged parts. Damaged parts are to be re-
placed and never repaired.
Only use original spare parts. Parts that are
not of the same quality can seriously dam-
age the equipment and compromise safety.
WARNING! During maintenance oper-
ations unplug the machine from the mains.
1. MOTOR COOLING
To avoid overheating and damage to the motor,
always keep the cooling air vents clean and free
of sawdust and debris.
2. MAINTENANCE AND SHARPENING
OF THE BLADE
WARNING!
Periodically check that the
blades are not bent or damaged and that the
xed comb on the blade is intact.
Adjustment of the distance between blades is not
necessary, as this is predetermined by the manu-
facturer.
If the blades are used correctly, following all the
instructions provided, they will not require any
maintenance work and will not need sharpening.
It is necessary to sharpen the blades only when
the trimming performance decreases and the
branches tend to stick together.
NOTE
Any intervention on the blade
should always be conducted at a specialised Cen-
tre that has the most appropriate tools and is able
to perform the operations without compromising
the safety of the machine.
3. ELECTRIC CABLES
WARNING!
Check the condition of the
The best results will be obtained with the blade
slightly inclined (5° - 10°) in the direction you are
cutting, proceed with a curved movement, slowly
and without interruptions, especially in the ca se of
very thick hedges.
4. LUBRICATING THE BLADES DURING
JOBS (Fig. 6)
If the trimming device overheats whilst working, it
is necessary to lubricate the internal surfaces of
the blades.
WARNING! This operation must only
be performed when the blades have stopped
running and the motor is switched o.
4. END OF OPERATIONS
When you have nished your work:
Switch o the motor as indicated above (Chap.
6).
WARNING! Allow the motor to cool
before storing in any enclosure.
To reduce re hazards, clean the machine
thoroughly to get rid of any remains of grass,
leaves or excess grease, never leave contain-
ers with the cut debris inside the storage area.
To increase the eciency and working life of the
blades, clean and lubricate them carefully after
each work session.
Use a soft cloth to clean the blades, along with
a brush to remove more dicult dirt and debris.
Lubricate the blades with suitable, non-polluting
oil were possible.
8. MAINTENANCE AND STORAGE
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alpina SHT 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alpina SHT 500 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info