731974
13
Verklein
Vergroot
Pagina terug
1/21
Pagina verder
PREPARING TO WORK / HOW TO START - STOP THE MOTOR
7
EN
1. CHECKING THE MACHINE
WARNING! Make sure the machine is
not plugged into the mains socket.
Before starting work please:
check that the mains frequency and voltage is
the same as the rating data on the “Identication
Plate” (see chap. 1 - 7.8).
check that the trigger switch and the safety
button (Only for SGT 600) should move freely
without forcing and return automatically and rap-
idly back to their neutral position;
(Only for SGT 600) check that the trigger
switch must remain locked until the safety but-
ton is pressed;
check that the cooling air vents are not ob-
structed;
check that the power cable and extension lead
are not damaged;
check that handgrips and protection devices
are clean and dry, correctly mounted and well
fastened to the machine;
check that the cutting devices and guards are
not damaged;
check that the machine is not showing signs of
wear or damage due to knocks or other causes,
and carry out the necessary repairs.
2. ELECTRICAL CONNECTIONS
DANGER! Electricity and moisture
are not compatible.
Always handle and connect electric cables
in dry conditions.
Keep electric sockets or cables away from
wet and damp areas (e.g. puddles or wet
ground).
The quality of the extension leads must be no less
than H07RN-F or H07VV-F, with a minimum sec-
tion of 1.5 mm and a recommended maximum
length of 30 m.
To avoid overheating, do not keep the extension
lead rolled up during use.
DANGER! The permanent connec-
tion of any electrical equipment to the mains
of a building must be installed by a qualied
electrician in conformity with the regulations
in force. Incorrect wiring can cause serious
injury and even death.
NOTE
(Only for SGT 600 ) When you release the switch,
the safety button is also released and the motor
stops.
STOPPING THE MOTOR (Fig. 4)
To stop the motor:
Release the switch (6).
FIRST unplug the extension lead (3) from the
mains socket (4) and THEN disconnect the
power cable (2) of the machine from the exten-
sion lead (3).
STARTING THE MOTOR (Fig. 4)
Before starting the motor:
Fasten the extension lead (1) to the cable clamp
on the rear handgrip.
FIRST connect the power cable plug (2) to the
extension lead (3) and THEN plug the extension
lead into the mains socket (4).
To start the motor:
Hold the machine rmly with both hands.
SGT 600: Press the safety button and then the
switch (6).
SGT 350: Press the switch (6).
6. HOW TO START - STOP THE MOTOR
5. PREPARING TO WORK
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alpina ATR 600 E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alpina ATR 600 E in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info