541378
20
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
20 WZ20S User Guide
Stereo Input channel
DUAL INPUTS A and B The stereo channel features two stereo inputs
with independent gain control and on/off switching. One source may be
selected at a time, or both may be mixed together further increasing the number
of simultaneous inputs to the mix. This means that you can leave two stereo
sources permanently connected to the console without the need to repatch or
readjust the gain settings.
GAIN A (B) Adjusts the channel input sensitivity to match the connected
source to the console 0dB operating level. This provides a 30dB range with
continuous adjustment for signals from 20dBu to +10dBu. Use the PFL system
to correctly set the gain using the console meters.
ON A (B) Switches stereo source A (RCA phono input) and/or stereo source B
(TRS jack input) on and routes it to the channel.
MONO Combines left and right to provide a mono signal from a stereo source,
or to feed a mono source to both channels.
EQUALISER The channel equaliser is a powerful tool to creatively tailor the
sound within the mix, or to deal with problems such as poor source
characteristics, noise and feedback. Start with the EQ controls set to their mid
(flat) position. Then adjust the EQ to achieve the sound you want. Take time to
experiment with the controls so you get to learn the effect the equaliser can
have on the sound.
The WZ20S stereo channel provides separate tone control over four fixed
frequency bands. The frequencies in each band may be boosted or cut by up to
15dB. The centre flat position is detented for quick resetting.
HF Turn this control clockwise to boost and anticlockwise to cut the high
(treble) frequencies. This has a shelving response with all frequencies above
the 12kHz turning point affected. Note that frequencies below 12kHz are
affected by a decreasing amount. Use HF boost to brighten up the sound by
adding sparkle to compensate for poor source material, or cut to reduce source
hiss or high frequency noise.
MF1 Turn the +/- control clockwise to boost and anticlockwise to cut the higher
mid frequencies. This has a bell shaped peak/dip response that has maximum
boost or cut at 2.5kHz. Boost to add presence, or cut to reduce harshness.
MF2 This is similar to MF1 but affects the lower mid frequencies centred on
250Hz. Boosting can enhance the warmth of the sound while cutting can clean
up a boomy sound.
LF Turn this control clockwise to boost and anticlockwise to cut the low (bass)
frequencies. This has a shelving response with all frequencies below the 60Hz
turning point affected. Note that frequencies above 60Hz are affected but by a
decreasing amount. Use LF boost to enhance low end punch, and cut to reduce
source hum and rumble.
EQ IN Switches the equaliser in or out of the signal path. Use this to check the
effect of the control settings by comparing the equalised and unequalised
signals.
ON
-15
-15
-15
60Hz
LF
-15
MF2
MF1
HF
12kHz
-10
-5
0
GAIN
+15
+15
+15
EQ
IN
0
+15
0
0
ON
0
MONO
20
15
10
5
GAIN
-10
-5
0
10
20
15
5
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Allen-Heath MixWizard Series WZ20S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Allen-Heath MixWizard Series WZ20S in de taal/talen: Engels als bijlage per email.

De handleiding is 4,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info