541348
9
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
GL2200 USER GUIDE
9
CONNECTING CHANNEL INPUTS
Both microphone and line sources such as keyboards, replay devices and effects processors
can be plugged into either the jack or XLR input for convenience. The channel accepts a wide
70dB range of source levels. The balanced 3-wire input provides the best immunity to
interference pickup on long cable runs.
CONNECTING TO INSERTS
You do not need to plug anything into the insert socket for normal operation. You may, however
wish to insert a signal processor such as a compressor/limiter or noise gate into the signal path
to prevent excessive peaks or to cut down source noise. The insert lets you do this by breaking
the signal path after the input pre-amp and before the EQ in the channel input or before the
fader in the Group and L-R section. Use a Y-lead or suitable TRS jack lead to connect to the
external processor. The insert operates at 0dBu line level in the channel input and –2dBu in the
Group and L-R section. Adjust the processor input and output levels for optimum signal level.
CHANNEL DIRECT OUTPUTS
The channel direct output taps the signal off post-fader (pre-fader if the internal link option is
changed) for connection to external processing or recording equipment. This is ideal for
multitrack recording during a live performance. Here each channel can be recorded on a
separate track for mixdown later. The output is impedance balanced on TRS jack. This means
that you get the benefit of interference immunity when connecting to outboard equipment with
balanced inputs. You can, of course, also connect to unbalanced equipment. The signal
operates at nominal 0dBu line level.
ADJUSTING THE LEVELS
For best performance it is important that the connected source signals are matched to the “normal
operating level” of the console. Similarly the console outputs should be correctly matched to the
operating levels of the connected amplifiers and destination equipment. If too high, the signal peaks
will be clipped resulting in a harsh distorted sound, and if too low, the signal-to-noise ratio is reduced
resulting in excessive background hiss.
For best results, operate the console with the meters averaging ‘0’ or just below and allowing the
loudest passages and occasional peaks into the ‘yellow’. Reduce the gain if the peak indicators flash
(red). The GL2200 provides +4dBu output level at the XLR outputs for a meter reading of 0VU. It is
advisable to adjust the power amplifier input gain or fit an attenuator pad if normal console operation
results in an output level too high for the connected amplifier. Normal operation should give rise to
fader levels around the ‘0’ mark.
The GL2200 has an advanced PFL (pre-fade listen) / AFL (after-fader listen) and channel metering
system to let you listen to and check the level of signals at different points in the signal path without
affecting the main outputs. Use the channel PFL switches to set up the input GAIN controls to read an
average ‘0’ (yellow LED). Signal activity is always shown on the channel meters regardless of fader
position. The green ‘SIG’ LED lights at -20dBu to indicate signal presence, the yellow ‘0’ LED
indicates normal level, and the red ‘PEAK’ LED warns of potential overload 5dB before clipping.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Allen-Heath GL2200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Allen-Heath GL2200 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info