707374
48
Verklein
Vergroot
Pagina terug
1/58
Pagina verder
48
Indoor unit:
Slide the battery cover at the rear downwards, insert 2 AA 1.5V batteries as indicat-
ed inside the battery compartment and replace the battery cover on the indoor unit.
(Batteries are not included)
The indoor unit now starts searching for the outdoor unit for 1 minute. Insert the
batteries into the outdoor unit within this minute.
Outdoor unit:
Open the battery compartment by loosening the top of the outdoor unit. Open the battery compartment by
removing the cover. Insert 3 AA 1.5V batteries according to the image above. Pay attention to the polarity (+
and -) while doing so. Replace the cover and secure the top back onto the base (batteries are not included).
Mount the sensor onto a pole (28~40 mm) using the clips with the large screws and bolts.
Preferably, install the outdoor unit at least 1.5m above ground level in an open space within the transmitting
range of the outdoor unit to the indoor unit, making sure it can freely catch the wind.
Remarks:
After replacing the batteries of the outdoor unit or after an interruption of the connection with the outdoor
unit, press the “SCAN” button on the indoor unit to reconnect the outdoor and indoor unit.
Avoid placing the unit in direct sunlight, rain or snow.
Try multiple locations to obtain the best possible reception between the outdoor unit (transmitter) and
indoor unit (receiver).
3.2 Paring the indoor unit / outdoor unit:
Automatically:
As soon as the batteries are inserted into the indoor unit, the indoor unit starts searching a signal from the
outdoor unit for 1 minute. So, when you insert batteries into the outdoor unit within this minute and the units
‘nd’ each other, these units will be paired automatically. The display of the indoor unit shows the tempera-
ture, humidity and wind speed as transmitted by the outdoor unit.
Manually:
If the units cannot automatically nd each other, or after replacing the batteries, you may pair the outdoor
unit with the indoor unit (again) as follows:
1. Press and hold the SCAN button for 2 seconds, the antenna symbol in the display starts ashing
2. Or alternatively briey press the RESET button at the bottom of the outdoor unit
3. After several seconds the units will nd each other (again)
3.3 Location:
Indoor unit:
You may choose to suspend the indoor unit from a wall with a simple screw or to use
it as a desk model with the supplied stand. In any case, never place the indoor unit in
direct sunlight or next to a heat generating light or stove.
Outdoor unit:
You may install the outdoor unit on a pole (excluded). In any case, make
sure to place the unit preferably 1.5 metres above ground level where it
can freely catch the wind.
AA 1,5V
AA 1,5V
AA 1,5V
reset
Not
included
48

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Alecto-WS-3400

Zoeken resetten

  • windmeter doet het niet ( cups draaien ), heb de batterijen vervangen en cups schoongemaakt en gereset dus hoop ik dat iemand weet wat ik evt meer kan doen bvd Ron Gesteld op 20-11-2021 om 03:32

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alecto WS-3400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alecto WS-3400 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 21,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info