P
Switching on/off:
press and hold for 2 seconds to turn off
V
Use the and buttons to set the loudness of the sounds
from the baby room that you hear through the speaker of the
parent unit.
While adjusting, the volume level will be indicated on the
display and the icon will appear in the upper part when the
volume level is set to 0 (no sound).
Switching on/off automatically: (VOX)
Y
ing quietly and the baby unit is not detecting any sound, and
let it turn on again as soon as the baby starts to cry
Here you can set the trigger level for turning on images and
sound:
1. Press the MENU button and use the or button to
scroll to the option
2. Use the and buttons to decrease or increase the
sensitivity level:
: low sensitivity
sounds are being detected
: high sensitivity
when low sounds are being detected
: maximum sensitivity
switched on
3. Press the MENU button to save your settings and leave
the menu
Switching the display on/off manually:
When the display is turned off because no sound is being de-
tected, but you would still like to check, you can briey press
the button to temporarily switch on the display
button again to turn the display off.
MUL
INTRODUCTION:
Y
on the DVM-67 parent unit. Separate cameras are available
via the service department of
erlands), 03 238 5666 (Belgium) or via internet www
Read paragraph 4.2 (Multi-camera) for instructions on how
you can use the parent unit to switch to the image from other
cameras.
REGISTERING ADDITIONAL CAMERAS:
1. Connect the power adaptor supplied with the camera to
the new camera and turn the camera on.
2. Press the MENU button on the parent unit and use the
or button to select the option.
3. Use the and buttons to select the number you want to
assign the camera to and press the MENU button.
4. An hourglass will appear on the display to indicate that the
parent unit is currently searching for the new camera.
5. Press and hold the P button on the baby unit until after
several seconds the image of the new camera appears on
the display of the parent unit.
The new camera is now registered and ready for use.
DEREGISTERING ADDITIONAL CAMERAS:
Follow the steps below to deregister faulty cameras or cam-
eras no longer in use:
1. Press the MENU button on the parent unit and use the
or button to select the option; the display will now
show the numbers of all registered cameras.
2. Use the and buttons to select the camera you want to
deregister
3. Press and hold the T button until X and V appear on
the display
4. Use the and buttons to select the V option to deregis-
ter the camera (or select X to cancel the deregistration)
5. Press the MENU button to conrm the deregistration.
TIPS AND WARNINGS
GENERAL:
• Thoroughly read the user
indications.
• Never place the baby unit or parent unit in wet or humid
room or environment.
• Ensure adequate heat dissipation; never cover the parent
unit, the baby unit and/or the power adapter(s) and never
place them directly next to a heat source.
• Only use the supplied adapter(s); connecting a different
type of adapter will damage the electronics.
• Make sure the adapter cables are free of any damage and
ensure nobody can trip or fall because of these cables.
• Never dismantle the parent unit, the baby unit and/or the
power adapter(s); only qualified personnel is authorized
to do so.
INST
• Only connect or disconnect the power adapter to/from
the baby unit or parent unit when the power adapter is
removed from the wall socket.
• Never install the DVM-67 during thunder storms.
• Never touch any non-isolated adapter cables, unless the
adapters are removed from the wall socket.
INTERFERENCE-FREE:
• This baby display monitor is digitally coded. This means
you will never receive signals from other devices, nor can
the signal from your baby unit(s) be received by e.g. your
neighbors.
• In case the baby unit(s) or parent unit is placed in or in the
close vicinity of electromagnetic fields, the signal (images
or sound) can be slightly affected. If this happens, try
a different location for the baby unit(s) or parent unit or
move, if possible, the source of the interference.
EA
• Eavesdropping/wiretapping of the signals from this baby
video monitor is nearly impossible. Not only must one be
within range of the baby video monitor
some very costly equipment.
MAINTENANCE:
• Only clean the baby monitor with a moist cloth; never
use chemical cleaners. Before any cleaning, you must
disconnect the adapters.
RANGE:
• The baby display monitor has a range of up to 300 meters
in an open field and up to 50 meters indoors; this range
depends on local circumstances. When the units get out
of range from each other
for several seconds (no motion) while flashes on the
display after another few seconds.
DELA
• The baby unit transmits the images and sound to the
parent unit in digital blocks. The parent unit converts
these signals back to a recognizable image and a
comprehensible sound. Therefore, there is a small delay
between the moment of movement and making sounds
and the display and sounds of the parent unit.
• Besides that, the sounds and images on the parent unit
are not exactly simultaneous.
ENVIRONMENT AND
• The packaging of this baby video monitor can be
discarded as waste paper
save this packaging so you can adequately protect the
devices for transportation.
• Faulty or exhausted batteries or battery packs
should be taken to your local depot for small
chemical waste or to dedicated battery collection
points. Never dispose of batteries or battery packs
as normal household waste.
• In case the baby video monitor is being replaced, please
return it to your supplier; they will guarantee environment-
friendly processing.
PROBLEMS:
• no image, no sound:
are the parent unit and baby unit switched off? (battery
charged, battery full?)
is the parent unit within range of the baby unit?
is the baby unit switched off because no sound is being
detected?
maybe the display of the parent unit is turned off with
the button?
is the volume at the parent unit set to 0 (off)?
• If the above is all in order, remove the adapters from the
wall sockets, take the rechargeable battery out of the
parent unit, wait at least one minute and then reconnect
everything. Now
on.
• If you still receive no images or sound, please contact
the customer service of
641
0085 (Germany) or via internet www
SPECIFICA
Range: up to 50 meters indoors
up to 300 meters outdoors
Parent unit power: 3.6V NiMH battery pack,
900mAh
6VDC 600mA
(incl.),
model: S003IV0600060
Baby unit power: 6VDC 600mA
(incl.),
model: S003IV0600060
Frequency: 2.4GHz, digital frequency
hopping (FHSS) / 21 channels
Display: 2.0” color LCD display
QVGA
Recharging time parent unit battery:
+/- 10 hours *
Life-span parent unit battery: 6~10 hours *
T 0°C - 50°C
Accuracy: ± 2°C (at 25°C)
*: the times mentioned above are references only and depend
on the usage, condition and quality of the batteries.
WARRANTY
For the
from the date of purchase. During this period, we guarantee
the free repair of defects caused by material and workmanship
errors.
importer
HOW T
user
please contact the supplier of this baby video monitor or
contact customer service of
641
(Belgium) or via the Internet www
THE W
of improper use, incorrect connections, leaking and/or
incorrectly installed batteries, use of unoriginal parts or
accessories, negligence and in case of defects caused by
moisture, fire, flooding, lightning and natural disasters. In case
of unauthorised modifications and/or repairs performed by
third parties. In case of incorrect transportation of the device
without adequate packaging and when the device is not
accompanied by this warranty card and proof of purchase.
The warranty does not cover connecting cables, plugs
and batteries.
consequential damages, is excluded.
USE
BABY
Switching on/off:
press and hold for 2 seconds to turn off
The green indicator on the baby unit ashes while the baby
unit is trying to establish a connection with the parent unit, this
indicator remains lit when the connection is successful.
V
Use the and buttons to adjust the reception volume for
the talk-back function from the parent unit.
Automatic night vision:
The baby unit is provided with built-in infra-red LEDs; these
LEDs will switch on automatically when the baby room turns
dark and will switch of again when it becomes light.
The LEDs can illuminate objects up to a distance of approxi-
mately 2 meters.
When it’s dark, that is when the night vision LEDs are
switched on, the images on the parent unit will be displayed in
black and white.
Attention: infra-red light cannot be perceived by the human
eye; that means you cannot tell whether the infra-red LEDs
are switched on with the naked eye. Depending on the type of
the infra-red LED, you might be able to see a red glow
T
The upper right corner of the parent unit’s display shows the
temperature of the baby’s room.
expressed in degrees Celsius or in degrees Fahrenheit:
1. Press the MENU button and use the or button to
select the option.
2. Use the and buttons to switch between °C and °F
3. Press the MENU button to save your settings and leave
the menu.
Don’t forget that the temperature is only an indication.
Multi-camera: (also see chapter 5)
In case you have registered multiple cameras on the parent
unit, you can follow the steps below to manually switch to
another baby unit or to automatically show the images of all
registered baby units one after the other:
1. Press the MENU button on the parent unit and use the
or button to select the option: the display will now
indicate the numbers of all registered cameras.
2. Use the and buttons to select the camera you want to
view or select to show all registered cameras one after
the otherMENU button.
The unit does NOT automatically switch to a camera
where sound is being detected.
Leaving the display switched on continuously:
If you don’t want the display to turn off automatically when no
sound is being detected, follow these steps:
1. Press the MENU button and use the or button to
select the option.
2. Use the and to switch between:
X: display is always turned on
V
3. Press the MENU button to save your settings and leave
the menu
T
With the display switched on, press the T button to talk
back to your baby
you are speaking and release the button to listen.
Y and
buttons.
Zoom function:
Press the button to turn on the zoom function (moving the
image somewhat closer) and press the button to turn off
the zoom function.
When the zoom function is switched on, the icon will ap-
pear in the upper part of the display
With the zoom function activated, press and hold the , ,
or button to move the image to the left, to the right, up or
down (attention: the camera doesn’t actually move, the display
merely shows another part of the available image).
Brightness:
1. Press the MENU button and use the or button to
select the option.
2. Press the and buttons to decrease or increase the
display brightness.
3. Press the MENU button to save your settings and leave
the menu.
Service Help
WWW
SERVICE@ALECT
NL 073 641
(Lokaal tarief)
BE 03 238 5666
(Lokaal tarief)
(T
DE 0180 503 0085
Lokale Festnetzkosten
Hesdo, Australiëlaan
5232 BB, ‘s-Hertogenbosch
The Netherlands
WWW
SERVICE@ALECT
NL 073 641
BE 03 238 5666
DE 0180 503 0085
Hesdo,
‘s-Hertogenbosch,
The Netherlands
(Lokaal tarief)
(T
(Lokaal tarief)
(Lokale Festnetzkosten)
v2.1
V1.1
