626267
14
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
14
Checking and changing glycol mixture. Regularly check the heating system’s uid level in the expansion tank.
The level should be about 1 cm above the minimum mark, with the heating system cold. The heating system should
be lled with a uid mixture made up from water and ethylene glycol. For best results, use high-quality ready-mixed
ethylene glycol (with inhibitors) intended for use in aluminium heating systems. The proportions when using concen-
trated ethylene glycol are 60% distilled water or water free from salts and 40% ethylene glycol. If the heating system
is exposed to temperatures lower than -25°C, a higher ethylene glycol content must be used, but not more than 50%.
Glycol mixture must be changed every other year as properties such as corrosion protection will deteriorate. If
Alde Premium Antifreeze is used, the change interval can be extended to ve years under normal operating condi-
tions. If the uid level is too low, the ethylene glycol content must be checked before topping up. This is to prevent
excessive concentration of ethylene glycol in the mixture. When topping up, use the same quality of ethylene glycol
mixture already in the system, alternatively use Alde Premium Antifreeze, which is compatible with most ethylene
glycol brands on the market. NB! Any vessels used for handling or mixing the liquid must be spotlessly clean,
and the pipes in the heating system must be free of contamination. This is to prevent the growth of bacteria
and corrosion in the system. The boiler must not be started if there is no ethylene glycol uid in the system.
Filling glycol. The system is lled through the expansion tank, Either manually or using the Alde lling pump
(1900811), which both tops up and bleeds the system. For manual lling, unfasten the circulation pump nut (R)
and then lift the pump *(S) out of the tank. Slowly pour the ethylene glycol mixture into the tank.
Bleed the system. Top up with more uid if the level has fallen after bleeding. Bleed a newly lled heating system
regularly during the rst days it is in operation.
Checking LPG system The LPG system should be checked regularly by a specialist, who will ensure that there
are no leaks from connections or hoses. LPG hoses should be changed as indicated on the date stamp, as they
tend to dry out and crack and are liable to leak as a result. For increased safety, we recommend tting an Alde leak
detector, type 4071, as close as possible to the reducing regulator.
Emptying the water heater. The boiler is tted with a built-in hot water heater which can hold approximately 8.5
litres of freshwater. The hot water heater can produce around 12 litres of 40°C water per half-hour (at a cold water
temperature of 10°C). If the electric elements are used instead of gas for heating the water heater, the capacity is
slightly reduced. The water in the water heater must be drained at least once a month in order to create a new
air cushion in the heater. The air cushion is used to absorb pressure surges in the heater. For emptying specially-
adapted boilers, as well as the vehicle’s general freshwater system, please refer to the manufacturer’s instructions.
NB! The hot water heater should always be drained completely when there is a risk of frost and when the
vehicle is not in use. The warranty does not cover frost damage.
NB! Note that the water in the water heater can be hot.
Draining the heater using the combined safety/drain valve: (see page 15)
Switch off the freshwater pump.
Open all water taps.
Then open the safety/drain valve by raising the yellow lever (M) to a vertical position, or by turning the knob (K)
180°. The heater will now drain directly below the vehicle through the safety/drain valve hose. Check that all the
water is emptied (about 7-10 litres). Leave the valve in the open position until the next time the heater is used.
NB! Check that the automatic non-return valve (N) is open and is allowing air to enter the heater when it is be-
ing drained, and that the hose is not blocked.
Bleeding the system. Depending on how the pipes have been tted, air pockets may form when the system is
lled with ethylene glycol uid. If the pipes only warm up a metre or so from the boiler, even though the circulation
pump is operating, it is a symptom of air trapped in the system. In a newly lled system, small air bubbles can form
in the expansion tank, resulting in a gurgling sound. Switch off the circulation pump for a few seconds to allow the
bubbles to disappear.
Bleed as follows: If a bleed screw is tted to the outgoing pipe of the boiler, open this screw and leave it open
until uid starts coming out. If the boiler is equipped with an automatic air vent, bleeding the boiler will take place
automatically. Start the LPG boiler. The circulation pump should be switched off. Open the remaining bleed screws
in the system (please refer to the instruction manual of the vehicle for their locations). Leave the bleed screws open
until ethylene glycol uid starts coming out of them, and then close them. Start the circulation pump and let it run
for a while. See if the pipes and radiators are heating up around the vehicle. If this does not help, you can try the
following method:
Single-axle caravan: Switch off the circulation pump. Tilt the caravan forwards. Leave it in this position for a few
minutes to allow the air to travel upwards in the system. Open the bleed screw located at the highest point. Leave
it open until ethylene glycol uid comes out. Proceed in the same manner but with the caravan tilted backwards.
Then position the caravan horizontally and start the circulation pump. See if the pipes and radiators are heating up
around the vehicle.
Motor caravan or twin-axle caravan. On these, the easiest way to bleed the system is to park the vehicle on slo-
ping ground or to raise one end of the vehicle using a jack. Bleed the system as described above.
12. CARE AND MAINTENANCE
Functions marked with a (*) are accessories, which are not installed on all vehicles, refer to the vehicle
manufacturer's instructions.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Alde-Compact-3020-HE---rev-1442

Zoeken resetten

  • Wij hebben een alde 3020 van 2015 en sinds kort panel failure 2 . Ze hebben bij de dealer de printplaat al vervangen . Maar nog steeds die zelfde fout . Gesteld op 5-4-2022 om 05:45

    Reageer op deze vraag Misbruik melden
  • Wij hebben net een carthago gekocht en heel de week de kachel op stroom gehad en nu zijn we onderweg en hebben wel gas op de koelkast en gasstel maar op de alde verwarming geeft hij Gas failure aan wat betekend dat Gesteld op 10-12-2020 om 20:07

    Reageer op deze vraag Misbruik melden
  • Goede middag wij hebben een alde Systeem
    Moet de boiler niet gereinigd worden vanwege kalk aanslag en waarmee !!!
    M vr gr Gesteld op 5-6-2020 om 19:04

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Alde Compact 3020 HE - rev 1442 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Alde Compact 3020 HE - rev 1442 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Alde Compact 3020 HE - rev 1442

Alde Compact 3020 HE - rev 1442 Gebruiksaanwijzing - Nederlands - 18 pagina's

Alde Compact 3020 HE - rev 1442 Gebruiksaanwijzing - Deutsch - 18 pagina's

Alde Compact 3020 HE - rev 1442 Gebruiksaanwijzing - Français - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info