4. Press NA key to select KEY BEEP and then press OK to select.
5. Press NA key to select ON or OFF and then press OK key to
confirm.
Activate/deactivate auto hang-up
This function enables you to end a call automatically by simply placing the
handset on the base station. By default, the
1. Press MENU key to enter menu selection.
2. Press NA key to select PERSONAL SET and then press OK
key to select.
3. Press NA key to select AUTO HANG-UP and then press OK
key to select.
4. Press NA key to select ON or OFF and then press OK key to
confirm.
Set date/time format
Y
format is DD/MM and 24 HOURS.
Set time format
1. Press MENU key to enter menu selection.
2. Press NA key to select CLOCK&ALARM and then press OK
key to select.
3. Press NA key to select SET FORMA and then press OK key
to select.
4. Press OK key to enter TIME FORMA. The current setting is displayed.
5. Press NA key to select 12 HOURS or 24 HOURS and then
press OK key to confirm.
Set date format
1. Press MENU key to enter menu selection.
2. Press NA key to select CLOCK&ALARM and then press OK key
to select.
3. Press NA key to select SET FORMA and then press OK key to
select.
4. Press NA key to select DA and then press OK key
to select. The current setting is displayed.
5. Press NA key to select DD/MM or MM/DD and then press OK
key to confirm.
Set alarm
The handset has an alarm clock feature, and when the alarm is set, the is
shown on the handset display
When the alarm time is reached, the display flashes --ALARM -- and the alarm
melody is played for 1 minute or until any handset key is pressed.
If the alarm is set for ON DAIL
If the alarm was set for ON ONCE, the will be turned off.
1. Press MENU key to enter menu selection.
2. Press NA key to select CLOCK&ALARM and then press OK key
to select.
3. Press NA key to select ALARM and then press OK key to select.
4. Press NA key to select OFF , ON ONCE or ON DAIL and then
press OK key to confirm.
If you select ON ONCE or ON DAIL, enter the time (HH-MM) for the alarm
and press the UP/DOWN key to select
format.
5. Press OK key to confirm.
Set alarm tone
1. Press MENU key to enter menu selection.
2. Press NA key to select CLOCK&ALARM and then press OK key
to select.
3. Press NA key to select ALARM TONE and then press OK key
to select.
4. Press NA key to select MELODY 1 , MELODY or MELODY 3
and then press OK key to confirm.
Advanced use of your telephone
Change Master PIN
The Master PIN is used for registration/unregistration of handsets. The default
Master PIN number is 0000. The maximum length of the Master PIN is 8 digits.
Note: If you forget your PIN code, you can reset it to its default 0000 using a
handset Reset (see section Reset Unit).
1. Press MENU key to enter menu selection.
2. Press NA key to select ADV and then press OK key
to select.
3. Press NA key to select CHANGE PIN and then press OK key to
select.
Enter the current Master PIN when prompted and then press OK key to confirm.
As you enter the PIN it will be shown as asterisks (*) on the screen.
(Enter the new PIN and then press OK key to confirm.
played.)
Register your handset
IMPORT
registered to the base, so you do not need to register them. Handset
registration is only necessary when you buy extra handsets or if a handset
has become faulty
The procedure described below is for V
may be different if you want to register another handset model, in which case
you should refer to its user guide.
Additional handsets must be registered to the base unit before you can
use them. Up to 4 handsets can be registered to one base station.
The Master PIN is required before you can register or unregister handsets.
By default, the Master PIN is 0000.
On the base station, press and hold the HANDSET LOCA
approximately 5 seconds.
1. On the handset, press MENU key to enter menu selection.
2. Press NA key to select ADV and then press OK
key to select.
3. Press NA key to select REGISTRA and then press OK
key to select.
Note : If no action is taken on the handset within 10 seconds, the
registration procedure will be aborted. If this happens, repeat the first step.
W is displayed on the screen.
indicate successful registration, and the handset will return to idle mode,
with its handset number displayed.
Note : If no base is found within a certain period, NO BASE will be
displayed with an error tone to indicate failed registration and the handset
returns to idle mode, and you will need to repeat the registration sequence.
Unregister your handset
1. Press MENU key to enter menu selection.
2. Press NA key to select ADV and then press OK
key to select.
3. Press NA key to select UNREGISTER and then press OK key
to select.
4. Enter the Master PIN when prompted and then press OK key to confirm.
(the default master PIN is 0000)
5. Press NA
then press OK key to confirm.
A
Note : If no action is taken on the handset within 15 seconds, the
unregistration procedure will be aborted and the handset returns to idle
mode.
Y
Change recall time
Y
T
leave the Recall T
standard recall required in the telephone network, but it can be changed to
Medium (270ms) or Long (600ms) if your telephone is connected to a PBX
that requires a different recall time.
1. Press MENU key to enter menu selection.
2. Press NA key to select ADV and then press OK
key to select.
CONFORMITY
This unit conforms to the following rules and regulations: 1995/5/EC Radio frequency and
telecommunication equipment and the mutual acceptance of conformity
The CE mark proves the above.
ENVIRONMENT
This symbol means that your inoperative electronic appliance must be collected
separately and not mixed with the household waste.The European Union has
implemented a specific collection and recycling system for which producers are
responsible.
This appliance has been designed and manufactured with high quality materials and
components that can be recycled and reused. Electrical and electronic appliances are liable
to contain parts that are necessary in order for the system to work properly but which can
become a health and environmental hazard if they are not handled or disposed of in the
proper way
household waste.
If you are the owner of the appliance, you must deposit it at the appropriate local collection
point or leave it with the vendor when buying a new appliance.
- If you are a professional user
- If the appliance is rented to you or left in your care, please contact your service provider
Keen to preserve the environment,
power supply
electricity consumption, but also a more compact format than the conventional power
supply units used by the previous range.
The used batteries from your telephone (if it has batteries) must be disposed of in
compliance with current environmental protection regulations. Comply with your local
regulations.
Return your batteries to your reseller or dispose of them at an approved recycling centre.
Help us protect the environment in which we live!
Model E100 / E100 Duo / T
E150 / E150 Duo / T
A/W No. : 10000330 Rev
Made in China
Delete a Call Log entry
1. Press in idle mode to go to the call list.
2. Press NA
3. Press NA key to select DELETE and then press OK key to select.
(Press OK key again to confirm.
Delete all entries in the Call Log
1. Press in idle mode to go to the call list.
2. Press MENU key
3. Press NA key to select DELETE ALL and then press OK key
to select.
(Press OK key again to confirm.
Using the intercom
Intercom, call transfer and conference are only possible with at least 2 handset
registered to the same base station. It allows you to make free internal calls,
transfer external calls from one handset to another
conference with two handsets and an external call.
If you try to make a call while another handset is already on an external call,
you'll hear a busy tone for a few seconds before the display returns to idle.
Intercom another handset
Press INT key in idle mode.
Intercom is established immediately if there are only 2 registered
handsets.
If there are more than 2 registered handsets, the handset numbers which
are available for intercom, and a * will be displayed. Press the specific
handset number you wish to call, or press to ring all handsets, to start
intercom.
T
During the call, press INT key to put the external call on hold
(the caller can no longer hear you).
Intercom is established immediately if there are only 2 registered handsets.
If there are more than 2 registered handsets, the handset numbers which
are available for intercom, and a * will be displayed. Press the specific
handset number you wish to call, or press * to ring all handsets, to start
intercom.
The store where you bought your telephone can also provide you with information and after-sales support.
SAFETY
In the event of an electrical hazard, the mains adapter acts as 230V power isolating device. It should
therefore, as a precaution, be installed close to the appliance and be easily accessible. To disconnect the
device from the primary power source, the mains adapter must be removed from the 230V AC/50 Hz socket.
If the mains adapter fails, it must be replaced by an identical model.
If not connected to the mains power or if there is a mains power failure, telephones that use cordless
handsets will not work.
You will then be unable to make or receive calls in the event of an emergency.
This is why we recommend that you also keep a conventional telephone – one that doesn’t require a power
supply – as a backup.
! Do not use your telephone to notify a gas leak when standing in the vicinity of the leak.
It is recommended that you avoid using this device during electrical storms.
Do not attempt to open the batteries, as they contain chemical substances. In the event of leakage,
avoid contact with the skin, eyes, nose and mouth. In the event of contact, rinse the affected part for about
twenty minutes with running water and seek urgent medical attention. Clean the product with absorbent
paper or a dry cloth and contact your reseller for replacement batteries.
ATLINKS hereby declares that the following models conform to the essential requirements and other
applicable provisions of European directive 1999/5/EC.
Versatis E100 / Versatis E100 Duo / Trio
Versatis E150 / Versatis E150 Duo / Trio
A
S.A.S. (Simplified Joined Stock Company) with capital of 500 000 Euros -
Registration number: 508 823 747 R.C.S. Nanterre.
©
The manufacturer reserves the right to modify the specifications of its products
in order to make technical improvements or comply with new regulations.
ALCA
The
license by
www.atlinks.com
If there are more than 2 registered handsets, the handset numbers which are
available for intercom will be displayed. Press the specific handset number
you wish to call to start intercom.
Press T
both internal callers can talk. Intercom is established.
Press and hold INT key for 2 seconds on the first handset to start the
three-party conference.
CONFERENCE will be displayed on the screen once the conference
call is established.
Handset T
Set the ring volume
There are 5 ringer volume options (OFF
LEVEL
1. Press MENU key to enter menu selection.
2. Press NA key to select PERSONAL SET and then press OK
key to select.
3. Press NA key to select HANDSET TONE and then press OK
key to select and show RING VOLUME. Press the OK key again to select.
4. Press NA
key to confirm.
Set the ring melody
There are 10 ring melodies available on your handset.
1. Press MENU key to enter menu selection.
2. Press NA key to select PERSONAL SET and then press OK key
to select.
3. Press NA key to select HANDSET TONE and then press OK key
to select.
4. Press NA key to select RING TONES and then press OK to
select.
5. Press NA key to your desired melody and then press OK key to
confirm.
Activate/deactivate key tone
A
key tone. By default, the key tone is ON.
1. Press MENU key to enter menu selection.
2. Press NA key to select PERSONAL SET and then press OK key
to select.
3. Press NA key to select HANDSET TONE and then press OK key
to select.
Press T
both internal callers can talk. Intercom is established.
Press HANG-UP/EXIT key on the first handset to transfer the external
call to the called handset. The external call is transferred.
Note : If there is no answer from the called handset, press INT key to resume
the external call.
Answer an external call during intercom
During intercom, a new call tone is emitted when there is an incoming external
call.
Press T
Connection with the external call is established.
Note : T
press INT key
Switch between an internal and external call
During the call, press key to switch between an internal or external
call.
Establish a three-party conference call
The conference call feature allows one external call to be shared with two
handsets (in intercom). The three parties can share the conversation and no
additional network subscription is required.
During an external call, press INT key to put the external call on hold
(the caller can no longer hear you).
T
Using the call log
T
and they will inform you also of any charges for it.Caller ID lets you see the
phone numbers of your callers on the handset display
in your Call Log afterwards.The Call Log stores the last 10 external calls,
whether or not you answered the call, so you can call them back later
Only the most recent call is saved if there are repeat calls from the same
number
entry
If you've got a new call in the Call Log, will appear on the handset display
If the received number is the same as one in your phonebook, the name from
the phonebook will display as well as the number
If a call is from someone who withheld their number
WITHHOLD ID.
If the call is from someone whose number is unavailable, or if you have not
subscribed to Caller ID but have set the date and time, the display will show
CALLING when it is received and UNA in the Call Log.
Access call log
Press in idle mode and press NA
The calls are displayed in chronological order with the most recent call at the
top of the list.
1. Press OK key time.
Save call list entry into the phonebook
2. Press in idle mode to go to the call list.
3. Press NA
4. Press NASA and then press OK key
to select (Enter the name of the contact (maximum 12 characters) and then
press OK key to confirm.
3. Press NA key to select RECALL TIME and then press OK key
to select.
4. Press NA key to select SHORT , MEDIUM or LONG and then
press OK key to confirm.
Reset unit
Y
Note: Upon reset, all your personal settings, call log and redial list entries will
be deleted and the phone will return to its default settings. However
phonebook will remain unchanged after reset.
1. Press MENU key to enter menu selection.
2. Press NA key to select ADV and then press OK
key to select.
3. Press NA key to select RESET and then press OK key to select.
4. Press OK key again to confirm.
reset to its default settings.
* Value vary according to environment.
** Depending charge.
Free field range Up to 300 meters*
Indoor range Up to 50 meters*
Handset battery
(average values)
7 hours alktime**
100 hours standby**
Number of Up to
Intercom mode Yes
Three -way confere
(1 outside
2 internal correspondents)
Yes
Electrical connection
Base mains adapter
Charger
Base: S003IV0600050 or IA5060
Charger: S003IV0600015 or IA5060
Input: 100-240 V 50-60 Hz
Output: 6V DC 500 mA(BASE)
6V DC / 150mA (charger) ; (500mA for IA5060)
Only use telephone.
Single-phase AC, excluding IT
the EN 60950 andard. Caution: the network vol tage is
classified as a hazard by the criteria of this standard.
T
Appliance designed for connection to a TNV3 class
(telecommunications network vol tage) analogue
telephone line EN 60950 andard.
Batteries Corun / – AAA – 1.2 V – mAh
Only use telephone.
Using any
explosion.
Used batteries
current environmen tal regulations.
Operating temperature From 5 40° C
T
If you have difficulty with your phone, please try the suggestions listed below
As a general rule, if a problem occurs, remove the batteries from all the
handsets in your installation for about 1 minute, then disconnect and reconnect
the power supply to the base and reinstall the handset batteries.
AL
Y
manual to install and set up your telephone.
All connectors are firmly inserted in their sockets.
Mains power to the base unit is switched on at the
socket.
The handset’s batteries are correctly and securely
installed and are not run down.
Everyday use
“I cannot make or answer calls”
“I cannot make a call”
“When I press on the keys,
nothing happens”
“The phone does not ring”
“I hear ‘beeps’
handset while I’m on a call”
“When I try to make a call, I
hear busy tone”
“The volume in the earpiece is
low when I’m on a call”
Batteries
“The handset’s battery cells
are running low within
an hour or two”
“I try to recharge the batteries
but I still get a warning that
they are low”
If the fault persists...
If the handset’s display is blank, it may have been
switched off. Press and hold the HANG-UP/EXIT
key to switch it back on.
Check that the base unit’s mains power adapter is
plugged in and power is switched on.
The base unit needs mains power for normal
operation of the phone
- not just for charging the batteries.
Make sure you are using the telephone line cable
supplied with your telephone. Other telephone line
cables might not work. Move the handset closer to
the base unit.
Check the battery level symbol on the display
is low
charger pod to recharge the batteries.
Switch off power at the mains socket, wait for a
short time and then switch back on. This may
solve the problem.
If the handset display shows KEYS LOCKED,
press and hold the * button to unlock it before you
make a call.
Only one handset (or the base unit) can be
connected to the outside line at a time. If another
handset is already using the line, you need to wait
until it has finished its call.
Make sure the batteries are fitted in your handset
If the Battery Level symbol on the display shows
‘low’, put your handset back on the cradle to
charge.
T
somewhere higher if possible, or further from other
electrical equipment.
T
Check that the base unit’s mains power adapter
is plugged in and power is switched on.
Check that ring volume is not on OFF
Y
Move closer or your call may be cut off.
Check the Battery Level symbol on the display
it’s low
If you’re using a multi-handset system, check
whether another handset is already on a call.
Make sure you’re holding the earpiece correctly
over your ear
Adjust the volume using the UP/DOWN key
Before you first use the handset, you should have
left it on the base unit or charger pod for 15 hours
to charge the batteries fully
replace the batteries. Check the connection
between the base unit and the mains power
socket. unit.
Y
used batteries safely – never burn them, or put
them where they could get punctured. Do not use
non-rechargeable batteries in your handset – they
may explode, causing damage.
Disconnect all other instruments connected to the
same line and try to make a call.
Disconnect the base unit from the telephone line
and plug a different phone into the master
telephone socket. T
the line is OK.
If the call does not work, and you are using a
two-way socket adapter
telephone directly into the socket.
If the call now works, the adapter may be faulty
you cannot make a call, the fault may be on the
exchange line. Contact the service provider
“When I key in a number
appears on the display
cannot make an outside call”
