601590
16
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
en
Power supply
16 456251_a
Do not deactivate safety and/or protective de-
vices of the machine.
Always ensure secure standing of the ma-
chine.
Never transport the shredder with the motor
running.
Switch the motor off, wait for the cutting disk
to stop moving, and disconnect the machine
from the mains connection prior to moving the
machine.
When moving the shredder, exclusively carry
the shredder on its handle.
Immediately disconnect the plug from the
mains if the extension cable has been dama-
ged or cut!
We recommend the connection via a earth le-
akage circuit breaker (ELCB) with a rated le-
akage current < 30 mA.
The mains voltage at your location must meet
the information regarding mains voltage in
the Technical Data. Do not use any other sup-
ply voltage.
The type of cable used should be 3 core dou-
ble insulated minimum of 1.5 mm to a maxi-
mum of 2.5 cross section to BS 6500 (1984)
tabel 16 PVC flex core. 300/500 V H05 W-F.
Any extension cable, up to a maximum of 50
m, should be of a type not lighter than the ca-
ble prescribed for the machine. The connec-
tor for the extension should be splash-proof.
Damaged or fragile extension cables may not
be used.
Check the condition of you extension cable
prior for every use.
Only use the mains connection for the desi-
gnated purpose. Do not pull the mains cable
in order to pull the mains plug out of the so-
cket. Protect the cable against heat and sharp
edges.
Always disconnect the shredder from the
mains connection when not in use.
Route the extension cable such that they do
not interfere and cannot be damage during
shredding.
Immediately switch off the shredder saw and
disconnect it from the mains connection if you
notice any changes.
Always ensure secure standing while
working. Do not bent forward to far.
Do not feed the shredder from an elevated
position.
POWER SUPPLY
The machine can be plugged into any 13 A mains
socket with 240 V ac, and must be protected by
a 13 A fuse. (TCS Duotec 3000: 400 V, Observe
correct direction of rotation)
Excluded from this are countries with a lower con-
nected load (10 A; 13 A, slowblowding).
WARNING!
Only for Great Britain (240 V)!
This machine must be earth!
Never use a faulty power cable!
Check the power cable regularly for
signs of wear and tear!
Wiring Instructions
When wiring the english 3 pin plug
please follow the instruction accor-
ding to the colour coding as shown
below:
Green and
Yellow to
terminal
E Earth
Brown to
terminal
L Live
Blue to
terminal
N Neutral
In accordance with VDE regulations, the machine
is fitted with a safety cutout switch which switches
off the power in the event of overload.
Overloading may occur if the blade is jammed for
a prolonged period of time. The safety switch is
designed to cause a delay of 1 - 3 minutes be-
for the motor can be restartet: Prior the restarting,
however the cause of overloading must be ascer-
tained and remedied.
To restart the motor, the switch must first be re-
turned to the OFF position, the after 2 or 3 minu-
tes the machine can be switched on again by swit-
ching the switch to ON.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Al-ko TCS Duotec 3000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Al-ko TCS Duotec 3000 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 1,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info