590226
10
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
PIPES CONNECTION
AND FLARRING THE PIPES
PIPE INSULATION
PIPES CONNECTIONS TO THE UNIT
EVACUATION OF PIPES AND INDOOR UNIT
Please use the pipe cutter for cutting the pipes.1.
Remove all burrs by using reamer. Gas leakage might 2.
happen If burrs are not removed! Turn pipes edge
down to avoid metal powder from entering down the
pipes.
After inserting the flare nut into the cooper pipes, 3.
please make a flare.
0.0-0.5mm
Bar
Coppet pipe
Coppet pipe
Reamer
To cut
Inclined
Surface
damaged
Cracked
Uneven
thickness
Please carry out insulation at pipe connection portion 1.
as mentioned in Indoor/ Outdoor Unit Installation
Diagram. Please wrap the insulated piping end to
prevent water from going inside the piping.
If drain hose or connecting pipes is in the room (where 2.
dew may form). Please increase the insulation by using
POLY-E FOAM with thickness of 9 mm or more.
Vinyl tape
Connecting to the indoor unit
Align the center of the pipes and finger tight the flare 1.
nut.
Use the torque wranch to tighten the nut firmely.2.
Connecting to the outdoor unit
Align the center of the pipes to the valves.1.
Use the torque wranch to tighten the valves firmely 2.
according to table:
Flare Nuts
Valve Cap
Service Port Cap
1/4
13-18
13-20
11-13
TUBE (Inch)
Torque(
N.m
)
3/8
40-45
13-20
11-13
1/2
60-65
18-25
11-13
5/8
70-75
18-25
11-13
3/4
80-85
40-50
11-13
After connection the unions of the indoor and outdoor units,
evacuate the air from the tubes and from the indoor unit is
follow:
Connect the charging hoses with a push pin to the low and high 1.
sides of the charging set and the service port of the suction and
liquid valves. Be sure to connect the end of the charging hose
with the push pin to the service port.
Connect the center hose of the charging set to a vacuum pump.2.
Turn on the power switch of the vacuum pump and make sure 3.
that the needle in the gauge moves from 0MPa (0cm Hg) to - 0.1
MPa (-76cm Hg). Let the pump run for fifteen minutes.
Close the valves of both the low and high sides of the charging 4.
set and turn off the vacuum pump. Note that the needle in the
gauge should not move after approximattely five minutes.
Disconnect the charging hose from the vacuum pump and from 5.
the service ports of the suction and liquid valves.
Tighten the service port caps from both valves, and open them 6.
using a hexagonal Allen wrench.
Remove the valve caps from both valves, and open them using 7.
a hexagonal Allen wrench.
Remount valve caps onto both of the valves.8.
Check for gas leaks from the four unions and from the valve caps. 9.
Test with electronic leak detector or with a sponge immersed in
soapy water for bubbles.
1. Charging set
2. Vacuum pump
3. OUTDOOR UNIT
4. Service valve
5. Cap
6. Suction valve
7. Service valve*
8. Cap
9. Liquid valve
10. INDOOR UNIT
11. Suction flare connection
12. Liquid flare connection
1
2
3
4
5
6
7
8
9
10
11 12
NOTE: For additional charge of various tubing
lengths, refer to outdoor unit table.
Sample

8
CUTTING
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Airwell Multisplit YAZE CINCO DCI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Airwell Multisplit YAZE CINCO DCI in de taal/talen: Engels als bijlage per email.

De handleiding is 1,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info