28962
11
Verklein
Vergroot
Pagina terug
1/75
Pagina verder
11
TRAINER SYSTEM
The Trainer system in the RD6000 Super transmitter allows you to connect any two Airtronics RD6000 Super together
for the purpose of training a new pilot. You can also connect the RD6000 Super to either an RD6000 Super, RD6000,
RD6000 Sport, VG 400, VG 600, Radiant or Vanguard PPM unit. The Trainer cord to use is the ATX Part # 97100.
The RD6000 Super is NOT compatible with Infinity 660 or Quasar units.
In actual use, one of the two transmitters will serve as the Master and the second transmitter will serve as the Trainer.
The Master transmitter is held by the instructing pilot, AND IS THE TRANSMITTER THAT MUST MATCH THE
RECEIVER FREQUENCY INSTALLED IN THE MODEL! The trainer transmitter is held by the learning pilot, and does
not need to be on the same frequency as the model. The frequency of the Trainer transmitter is unimportant because
the switch of the trainer transmitter is
NOT turned on during instructional flying. Normally during training, the
instructor takes the model off and flies it to a reasonable altitude. While the Master/Trainer switch on the Instructors
transmitter is left in its OFF position, the Master transmitter will have full control of the model. When the instructor is
ready to begin training, he presses and holds the spring loaded switch on his transmitter which transfers control to the
student.
(As long as the instructor holds his Trainer switch in the ON position, the model will respond to the commands of the
Trainer transmitter sticks allowing the pupil to fly the model. It is not necessary for the student to hold the trainer
switch on the Trainer transmitter.)
When the instructor ceases to stop training, or if he feels that the student is in a situation that endangers the model, the
instructor can release the spring loaded switch and control of the model will immediately return to the Master transmitter.
To use the Trainer system, you must plug the appropriate Trainer cable into the back of both the Master and the Trainer
transmitters. Turn on the Master transmitter and the Model. The cable will energize the encoder section of the Trainer
transmitter. Once you have verified that both the Master and the Trainer transmitters will control the model when the
spring loaded switch in the appropriate position you are ready to start training.
NOTE:
Both transmitters must be programmed identically for the trainer system to function properly. All servos must operate in
the same direction, centering, end points, and other settings such as type of Modulation must be identical.
Trainer Switch
(Spring Loaded)
Master Transmitter
Trainer Transmitter
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Airtronics RD6000super bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Airtronics RD6000super in de taal/talen: Engels als bijlage per email.

De handleiding is 6,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info