289944
3
Verklein
Vergroot
Pagina terug
1/70
Pagina verder
DC-2030m
User manual
AgfaPhoto DC-2030m
i
Thank you for purchasing this AgfaPhoto digital camera. Please read these operating instructions
carefully in order to use the digital camera correctly. Keep the instructions in a safe place after
reading so that you can refer to them later.
Precautions
Do not aim the camera directly into the sun or other intense light sources which could
damage your eyesight.
Do not try to open the case of the camera or attempt to modify this camera in any way.
High-voltage internal components create the risk of electric shock when exposed.
Maintenance and repairs should be carried out only by authorized service providers.
Do not press the flash too close to the eyes of animals or young children. Eye damage may
result. Please remain at least one meter away from infants when using flash.
Keep the camera away from water and other liquids. Do not use the camera with wet hands.
Never use the camera in the rain or snow. Moisture creates internal danger and may cause
electric shock.
Keep the camera and its accessories out of the reach of children and animals to prevent
accidents or damage to the camera.
If you notice smoke or a strange odor coming from the camera, turn the power off immediately.
Take the camera to the nearest authorized service center for repair. Never attempt to repair
the camera on your own.
Use only the recommended power accessories. Use of power sources not expressly
recommended for this equipment may lead to overheating, distortion of the equipment, fire,
electrical shock or other hazards.
Disclaimer
We assume no responsibility over and above the provisions of the Product Liability Law for
damages suffered by the user or third parties as a result of inappropriate handling of the product
or its accessories, or by their operational failure and by their use. We reserve the right to make
changes to this product and its accessories without prior notice.
Warning!
Never disconnect to open the camera or remove any parts of it. This will invalidate all guarantee
claims.
AgfaPhoto DC-2030m
i
i
Contents
GETTING STARTED 1
USING THIS MENU 1
CONTENTS 2
PARTS OF THE CAMERA 3
INSERTING THE BATTERIES 5
LOW BATTERY INDICATOR 5
ABOUT BATTERY TYPE 5
INSERTING THE MEMORY CARD 6
ABOUT CAMERA MEMORY 7
DCF PROTOCOL 7
SETTING THE DISPLAY LANGUAGE / DATE &
TIME 7
SETTING THE DISPLAY LANGUAGE 7
SETTING THE DATE & TIME 8
USING THE LCD MONITOR 9
REC MODE 9
PLAYBACK MODE 10
CHANGING THE LCD STATUS 11
BASIC OPERATION 12
TURNING THE POWER ON AND OFF 12
POWER SAVING FUNCTION 13
CHANGING THE MODE 13
SWITCHING BETWEEN REC MODE AND
PLAYBACK MODE 13
SELECTING THE REC MODE 14
USING THE MENUS 16
REC MENU 16
SETUP MENU 17
BASIC RECORDING 21
RECORDING STILL IMAGES 21
USING SMILE CAPTURE MODE 22
TO ACTIVATE SMILE CAPTURE 22
USING INTELLIGENT SCENE MODE 23
TO ACTIVATE INTELLIGENT SCENE 23
USING BLINK DETECTION MODE 24
TO ACTIVATE BLINK DETECTION 25
USING THE Q MODE 26
SETTING IMAGE SIZE AND QUALITY 27
USING THE ZOOM FUNCTION 28
USING THE FLASH 29
USING THE MACRO 30
USING THE SELF-TIMER & BURST 31
USING THE APERTURE PRIORITY 32
USING THE SHUTTER PRIORITY 33
USING THE MANUAL EXPOSURE 33
USING THE STABILIZER 34
RECORDING MOVIE CLIPS 34
SETTING THE MOVIE SIZE 35
YOUTUBE® MODE 35
RECORDING AUDIO CLIPS 36
PLAYING BACK AUDIO CLIPS 36
RECORDING A VOICE MEMO 37
PLAYING BACK A VOICE MEMO 38
OTHER RECORDING FUNCTIONS 38
SETTING THE METERING 38
SETTING THE WHITE BALANCE 38
SETTING THE ISO 40
SETTING THE EXPOSURE 40
SETTING THE AEB 40
SETTING THE HIGHLIGHT 40
SETTING THE SHARPNESS 41
SETTING THE PHOTO EFFECT 41
SETTING DATE STAMP 41
SETTING FACE TRACKING 42
SETTING PHOTO FRAME 42
SETTING AF LAMP 42
AgfaPhoto DC-2030m
iii
PLAYBACK 43
PLAYING BACK IMAGES 43
PLAYING BACK MOVIE CLIPS 43
MAGNIFYING & TRIMMING STILL IMAGES
44
VIEWING IN THUMBNAIL 45
PLAYING A SLIDE SHOW 45
DELETING FILES 46
DELETING A SINGLE FILE 46
DELETING MULTIPLE FILES 47
DELETING ALL FILES 48
PROTECTING A SINGLE FILE 48
PROTECTING ALL FILES 49
PROTECTING MULTIPLE FILES 49
EDITING IMAGES 50
ROTATING STILL IMAGES 50
CHANGING THE IMAGE SIZE 51
CHANGING THE IMAGE WITH EFFECTS 51
CHOOSING THE IMAGE WITH PHOTO
FRAME 52
COPYING THE FILES 53
SETTING THE DPOF 54
CHOOSING A STARTUP IMAGE 55
MAKING CONNECTIONS 56
CONNECTING THE CAMERA TO A TV 56
CONNECTING THE CAMERA TO A PC 57
USING THE CARD READER 57
CONNECTING THE CAMERA TO A
COMPUTER WITH THE USB CABLE 57
APPENDIX 58
ABOUT THE FOLDER & FILE NAME 58
FOLDER STRUCTURE 58
FILE NAMING 59
TROUBLESHOOTING 60
SPECIFICATIONS 61
CUSTOMER CARE 63
COPYRIGHT 64
TRADEMARK RECOGNITION 64
DISPOSAL OF WASTE EQUIPMENT BY
USERS IN PRIVATE HOUSEHOLDS IN THE
EUROPEAN UNION 64
FCC COMPLIANCE AND ADVISORY 64
DECLARATION OF CONFORMITY 65
AgfaPhoto DC-2030m
1
Getting Started
Using This Menu
Getting Started
This section contains information you should know before using this camera.
Basic Operation
This section explains all recording features of this camera.
Basic Recording
This section explains how to record still images, movies, and audio files.
Other Recording Functions
This section explains common operations about recording images.
Playback
This section explains playback, delete, and edit functions of still images, movies and
audio files.
Making Connections
This section tells you how to connect this camera to a computer or TV.
Appendix
This section describes the troubleshooting and the camera specification.
The meanings of the symbols used in this user's manual are explained below:
This indicates cautions that should be read before using these
functions.
This indicates the useful information when using this camera.
This indicates the reference page.
T
T
i
i
p
p
s
s
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
2
Contents
AgfaPhoto DC-2030m USB Cable AV Cable
Soft Case Strap
2 x AA Batteries
Software Installation
CD-ROM
Quick Guide
y Actual accessories may be different.
y Note that the shape of the charger plug depends on the area where you
purchased the camera.
y Do not swing the camera around by the strap.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
3
Parts of the Camera
1. Flash ( page 29)
2. Microphone
3. Lens
4. AF Lamp / Self-timer Lamp
5. Zoom Button ( page 28)
y Thumbnail (
page 45)
y Playback Zoom
(
page 44)
6. Playback Button
(
page 13)
7. Operation Lamp
8. Mode Button (
page 13)
y Delete Button (
page 46)
9. Menu Button (
page 16)
10. LCD Monitor (
page 9)
11. Flash Button (
page 29)
12. SET/DISP Button
(
page 11)
13. Macro Button (
page 30)
AgfaPhoto DC-2030m
4
14. Speaker
15. Power Button (
page 12)
16. Stabilizer
17. Shutter Button
(
page 21, 34)
18. USB/AV Terminal
(
page 20, 57)
19. Strap Ring
20. Memory Card Slot Cover
(
page 6)
21. Tripod Socket
22. Battery Cover (
page 5)
AgfaPhoto DC-2030m
5
Inserting the Batteries
Open the battery cover.
y Slide the battery cover in the
direction indicated by the
arrow.
Insert the batteries.
y Insert two AA-size batteries
with the positive (+) and
negative (-) poles matching
the directions indicated
inside the battery room.
Close the battery cover.
Low Battery Indicator
A low battery indicator
appears on the LCD screen when the batteries are nearly
exhausted. Batteries should be replaced promptly when the low battery indicator
appears.
About Battery Type
After replacing the batteries, please check the Battery Type in the setup menu (
page 20).
y Risk of explosion if battery is replaced by an incorrect type dispose of used batteries
according to the instructions.
y Be sure to turn off the camera power before insert or remove batteries.
y It is recommended to use the provided battery. For other compatible batteries, please
refer to Battery types. (
page 20). Use of any other type battery is not recommended.
y Replace all batteries at the same time. Never mix old and new batteries.
y Remove batteries if you will not be using them for a long time.
y The camera body may feel warm after extended use. This is normal.
y The type of battery and the battery power level may cause the lens to be stuck up.
Ensure you use the correct battery type and use a fully charged battery.
1
2
3
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
6
Inserting the Memory Card
Expand your camera’s storage by using SD or SDHC memory cards.
Open the SD Card cover.
y Slide the battery cover in the
direction indicated by the
arrow.
Insert the card.
y Insert the card with the label
facing up and the arrow
pointing in.
y To remove the card, gently press on the edge of the card and release it. Pull the
card out and close the SD Card cover.
Close the SD Card cover.
y It may cause damage to the card if removed while the camera is on.
y Do not touch the connection terminals on the back side of the card.
y Not all cards may be compatible with your camera. When purchasing a card,
please check the card's specifications and take the camera with you.
1
2
3
C
C
a
a
u
u
t
t
i
i
o
o
n
n
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
7
About Camera Memory
This camera is equipped with internal memory. If the memory card is not inserted in the
camera, all images and movie clips recorded by the camera will be stored in the internal
memory. If the memory card is inserted, images and movie clips are stored on the
memory card.
DCF Protocol
The DCF protocol defines the format for image file data as well as the directory structure
for the memory card. Images that are taken by a DCF camera can be viewed on
DCF-compatible cameras from other manufacturers.
Setting the Display Language / Date & Time
When using the camera for the first time after purchasing, be sure to choose a language
and set the date & time before using the camera.
Setting the Display Language
Turn the power on, and set the
camera to the Setup Menu
(
page 17).
Select [
Language].
y Press
or to select
[LANGUAGE] then press
or the SET button to launch the
submenu.
Select a language.
y Press
or to select a language and press or the SET button to
apply the setting.
Press the MENU button to close the menu.
1
3
2
4
AgfaPhoto DC-2030m
8
Setting the Date & Time
Turn the power on, and set the
camera to the Setup Menu
(
page 17).
Select [
Date & Time].
y Press
or to select
[Date & Time] then press
or the SET button to launch
the submenu.
Set date and time.
y Press
or to change the value of the cursor located. Press or
to move the cursor between settings.
y Holding down
or changes the values continuously.
y For date stamp setting (
page 41).
Apply the setting.
y After adjusting the settings, press the SET or the MENU button to apply
the setting.
y If the batteries are removed for longer than 48 hours, the Date and Time will
need to be re-set.
1
2
3
4
T
T
i
i
p
p
s
s
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
9
Using the LCD Monitor
The LCD monitor is used to compose images while recording, adjust settings and replay
images. The following indicators may appear on the LCD monitor while recording or
playing back images.
REC mode
1
Recording mode (
page 13)
14
Shutter speed ( page 21)
2
Flash (
page 29)
15
Shake warning ( page 21)
3
Macro (
page 30)
16
Aperture value ( page 21)
4
Self-timer / Burst (
page 31)
17
Face tracking ( page 42 )
5
Zoom indicator (
page 28)
18
Exposure ( page 40)
6 Shots remaining 19
Focus area (
page 21)
7
Battery (
page 5)
20
Date stamp ( page 41)
8 Storage media 21
AEB (
page 40)
9 Stabilizer 22
Sharpness (
page 41)
10
Metering (
page 38)
23
Quality ( page 27)
11
ISO (
page 40)
24
Resolution ( page 27)
12 Histogram 25
AF Lamp (
page 42)
13
White balance (
page 38)
AgfaPhoto DC-2030m
10
PLAYBACK mode
1
Playback mode (
page 13)
7
Recording info ( page 11)
2
Protect (
page 48)
8 Histogram
3
Voice memo (
page 37)
9 Captured date & time
4 File number / Total 10
Voice memo control (
page 37)
5
Battery (
page 5)
11
DPOF ( page 54)
6 Storage media 12
Resolution (
page 27)
y Some information may not display correctly if you display images captured by
other camera model.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
11
Changing the LCD Status
Press the SET/DISP button changes the LCD status as shown below:
REC mode
(A) OSD on (B) Full OSD (C) Guide line (D) OSD off
y Use the “Guide line” to compose images easily before shooting images.
PLAYBACK mode
(A) OSD on (B) Full OSD (D) OSD off
y You cannot change the LCD status in the following situation:
Manual exposure
Recording movie clips or audio files
Playing movie clips or audio files
Playing the slideshow
Viewing in thumbnail
Trimming a still image
T
T
i
i
p
p
s
s
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
12
Basic Operation
Turning the Power On and Off
Press the POWER button (n) to turn on
the camera in the REC mode.
y The power turns on, the lens extends
and the LED lights in green.
Press the PLAYBACK button (o) to turn
on the camera in the PLAYBACK mode.
y The power turns on, and an image
displays on the LCD monitor (p).
Press the POWER button (n) again to turn the power off.
y The power turns off, the lens retracts and the LED turns off.
y You can turn on the camera without the start-up and operating sound by
pressing and holding the POWER (n) or the PLAYBACK (o) button over 1.5
seconds.
y Switch between REC mode and PLAYBACK mode (
page 13).
1
2
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
13
Power Saving Function
For saving the battery power, the LCD monitor automatically turns off 1 minute after the
last control accessed (factory-preset setting). Press any button other than the power
button to turn on the LCD monitor. You can change the power save setting in Setup
menu (
page 19).
After the power saving function has been active for 1 minute, the power will turn off
completely. Press the POWER (n) or the PLAYBACK (o) button to restore the power.
The power save feature will not activate in the following situation:
y Recording movie clips or audio files
y Playing movie clips or audio files
y Playing the slideshow
y Connecting the camera to a computer or printer with the USB cable
Changing the Mode
You can record images and voices in the REC mode. And using the PLAYBACK mode to
replay, delete, or edit images on the LCD monitor.
Switching between REC mode and PLAYBACK mode
In REC mode, press the PLAYBACK button
(n) to switch to the PLAY mode.
In PLAY mode, press the PLAYBACK (n)
or the MODE (o) button to switch to the
REC mode.
AgfaPhoto DC-2030m
14
Selecting the REC mode
Set the camera to the REC mode
(
page 13).
Launch the mode palette.
y Press the MODE button (o) to
show the scene mode palette.
Select a mode.
y Use the four-way control to select a desired mode and press the SET
button to confirm the setting.
Display Title Description
Program The camera makes settings suitable for the shooting conditions.
Movie For recording movie clips.
Voice REC For recording audio.
Q Mode Allows beginners to take pictures easily.
Portrait Blurring the background to focus on the subject.
Landscape Used for the wide scenic views.
Sunset Enhance the red hue for recording sunset images.
Backlight Shooting the image of backlight object by changing metering.
Smile
Capture
Capture the most brilliant smile of characters.
Kids Take a still image to capture moving kids.
Night Scene Shooting the subject while keeping the background night scenery.
Fireworks Slow shutter speed to take fireworks exploding.
1
3
2
AgfaPhoto DC-2030m
15
Display Title Description
Snow Used for the beach or snow scenes.
Sports Used to take still pictures in high speed motions.
Party Used for the wedding or indoor parties.
Candlelight To capture the warmth effects of candle light.
Night
Portrait
Use to take portrait pictures when the background is darker.
Soft Skin Enhance the tone of skin so that the facial skin appears smooth.
Soft Flowing
Water
Can take pictures with effects as smooth as silk.
Food Higher saturation makes food more appetizing.
Building Enhance the edges of the subject.
Text Enhance the black & white contrast.
Auction Records small-size images that are perfect for auction notices.
Blink
Detection
This feature detects if the subject blinked an eye when the image
is captured and gives the user an option whether to save it or not.
Intelligent
Scene
The camera detects the shooting conditions and automatically
switches to the appropriate scene mode.
Aperture
Priority
The camera automatically adjusts an aperture value to match the
brightness
Shutter
Priority
The camera automatically adjusts the shutter speed to match the
brightness.
Manual
Exposure
This feature lets users adjusts the shutter speed and aperture
value to correctly expose your images.
AgfaPhoto DC-2030m
16
Using the Menus
When a menu is displayed, the four-way control and the SET button are used to make
the desired settings.
REC menu
Turn the power on, and set the
camera to the REC mode
(
page 13).
Open the REC menu.
y Press the MENU button (n) to
display the menu.
Select an item.
y Press
or (o) to select a
menu item.
Change the setting.
y Press
or (o) to change the setting.
Press the MENU (n) or the SET (o) button to save the settings and close
the menu.
REC menu list (Still Image)
Menu Item Available Setting Page
Resolution
/ / / / / /
27
Quality
/ /
27
Metering
/ /
38
White Balance
Auto /
/ / / / /
38
ISO
Auto / ISO125 / ISO200 / ISO400 / ISO800 /
ISO1600 / ISO3200
40
Exposure ... 40
Drive Mode
Off /
/ / /
31
4
5
1
2
3
AgfaPhoto DC-2030m
17
AEB
Off /
40
Highlight
Off /
/ /
40
Sharpness
/ /
41
Effect Off / B&W / Sepia / Red / Green / Blue 41
Date Stamp Off / Date / Date & Time 41
Digital Zoom Off / On 28
Face Tracking Off / On 42
Photo Frame Off / Frame 1 ~ 10 42
AF Lamp Auto / Off 42
REC menu list (Movie)
Menu Item Available Setting Page
Movie Size
/ /
35
Metering
/ /
38
White Balance
Auto /
/ / / / /
38
Setup menu
Turn the power on, and set the
camera to the REC or
PLAYBACK mode (
page 13).
Press the MENU button (n) to
open the REC or PLAYBACK
menu.
y The menu displays depends
on whether you are in the REC
mode or the PLAYBACK
mode.
Open the Setup menu.
y Press four-way control (o) to select SETUP (
) and then press the SET
(o) button to display the Setup menu.
3
1
2
AgfaPhoto DC-2030m
18
Select an item.
y Press
or (o) to select a menu item and then press or the SET
(o) button to launch the submenu.
Change the setting.
y Press
or (o) to select an option and press or the SET (o)
button to apply the setting.
Press the MENU (n) button to close the menu.
4
5
6
AgfaPhoto DC-2030m
19
Setup menu list
Menu Item Functions
Sounds
[Shutter]:
[Start-up]:
[Beep]:
[Volume]:
Sets the shutter sound on and off.
Sets a type of the start-up sound.
Sets the operation sound on and off.
Adjusts the volume of the shutter sound, start-up
sound, beep and playback sound.
Auto Review
[Off]:
[1 sec.]:
[3 sec.]
[5 sec.]:
The captured image will not automatically display after
shooing.
The captured image will display for 1 second after
shooting.
The captured image will display for 3 seconds after
shooting.
The captured image will display for 5 seconds after
shooting.
Power Save
[Off] / [1 min.] / [3 min.] / [5 min.]:
For power consumption, the camera is turned off automatically
for a period of time.
y The power save feature will not activate in some situation
(
page 13).
Date & Time
Sets the date & time (
page 8).
Language
Select a language for display menus and other information from
the following 21 languages: (
page 7)
Use this function if the camera experiences a “Folder cannot be
created” error or if you want to restart numbering, for example,
after erasing all files.
[Series]:
[Reset]:
Store the latest used file number no matter deleting
files or inserting a new memory card.
Reset file numbering each time the memory card is
changed.
File No.
y Resetting the file number is useful for avoiding the file name
duplication when images are downloaded to a computer
(
page 58).
TV Out
You can review images on a television with a supplied AV cable
(
page 56). TV Out should be set to either NTSC or PAL
AgfaPhoto DC-2030m
20
Menu Item Functions
depending on your region.
[NTSC]:
[PAL]:
America, Japan and others
Europe, Oceania and others
USB
[Computer] / [Printer]:
Sets the USB mode to connect the camera with a printer or
computer (
page 57).
S.Image
Sets a recorded image as the start-up image (
page 55).
Format
To erase all data stored in the memory card if you are using a
card, or all data stored in the internal memory if there is no card
inserted.
y A “BUSY...PLEASE WAIT” message displays and the
memory card is starting format.
y A “COMPLETED” message displays when finish formatting.
y All data will be deleted including protected files. Be sure to
download important files to your computer before formatting.
[Off] / [On]:
LCD Save
Enable the LCD save function to automatically decrease the LCD
brightness to conserve battery power
When the camera is idle for 5 seconds, the LCD darkens.
To ensure the camera displays battery level correctly, set the
type to match the batteries used.
Battery Type
Alkaline / NiMH / Lithium / Qxyride
Reset All
Resets the entire menu and button operation settings to initial
default.
The following settings do not change after Reset All:
y Date & Time setting
y Language setting
y TV out setting
y Battery Type
AgfaPhoto DC-2030m
21
Basic Recording
Recording Still Images
Turn the power on, and set the
camera to the REC mode
(
page 13).
Compose the subject on the
monitor.
y Aim the focus area (n) to the
subject that you want to take.
Half press the shutter button to focus the image.
y The focus area (n) becomes green while in focus, then shutter speed (o),
aperture value (p) and ISO value (q) are displayed.
y If the shutter speed is slow or the possibility that image may be blurred, the
shake warning icon
may appear on the LCD monitor. To avoid this, use
a tripod to stabilize the camera when recording images.
Take a picture.
y Press the shutter button fully to
take a picture.
y Make sure that your fingers or
the wrist strap does not block the
lens.
3
4
1
2
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
22
Using smile capture Mode
The smile capture model uses smile tracking to automatically capture images.
Pressing the shutter button will enable the camera to take 6 continuous shots whenever
a smile is detected. This feature is most useful in capturing different angles and smiles of
moving people. When capturing an image with more than one person, the camera
detects the smile of the closest person on the center of the screen
To activate smile capture
Select
from Scene Mode
submenu. (
page 13).
Focus the camera on the subject
to capture.
Press the shutter button to start
smile detecting. The smile
capture icon blinks every second
and the white focus frame turns
green to denote camera activity.
When a smile is detected, the camera will automatically take a shot of the
image. It will continuously take 6 shots whenever a smile is detected
.
To stop shooting before the 6 shots are taken, press the shutter button
again, The smile capture icon stops blinking and the focus frame turns
white.
y When capturing an image with several faces, face tracking function may take up
more time tracking faces for the first time.
1
2
3
4
5
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
23
Using Intelligent Scene Mode
With the Intelligent Scene Mode, the camera automatically detects the shooting
conditions and switches to the appropriate scene and settings when aiming on a subject.
This feature is most useful for novice users to capture great images even without basic
knowledge of photography
To activate Intelligent Scene
Select
from Scene Mode
submenu. (
page 13).
Focus the camera on the subject
to capture.
The camera detects the shooting
conditions and switches to an
appropriate scene mode.
Half press the shutter button to focus the subject. The frame turns green
to indicate focus is set.
Press the shutter button to take the shot.
The table below shows the modes supported by intelligent scene:
Icon Intelligent Scene Modes Description
Portrait This mode is set when a face is detected.
Backlight
This mode is set when a face is detected with an EV
setting greater than 2.5.
Landscape
This mode is set when:
y There is no face detected.
y The focus distance is more than 1.5 meters.
y The EV setting is greater than 11 or 10.5.
Macro
This mode is set when:
1
2
3
4
5
AgfaPhoto DC-2030m
24
Icon Intelligent Scene Modes Description
y There is no face detected
y The focus distance is within the macro range.
This mode can only be detected when you half press
the shutter button.
Night Scene
This mode is set when:
y There is no face detected
y The focus distance is more than 1.5 meters.
y The EV setting is lower than 5 or 4.5.
y After the camera detects the shooting conditions, this icon changes to show the
detected scene mode.
y Face tracking is automatically enabled.
Using Blink Detection Mode
The Blink Detection mode tracks faces and determines captured image that contain
subjects with blinked eyes. After shooting, when the camera detects that the subject
blinked an eye, a menu selection appears to ask the user whether to save the image or
not. This feature saves time in managing photos to be stored or deleted from the
memory.
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
25
To activate Blink Detection
Select
from Scene Mode
submenu. (
page 13).
Half press the shutter button to
focus the subject. The frame
turns green to indicate focus is
set.
Press the shutter button to
capture the image. The image is
automatically saved unless the
camera detects that the subject
blinked an eye.
Select Save Image to save or Cancel to disregard.
1
2
3
4
AgfaPhoto DC-2030m
26
Using the Q mode
The Q mode provides a simplified camera
interface. Larger icons and fewer controls
make it easier to take pictures anytime,
especially for the beginners and elder
users.
You can use only the basic settings in the Q
mode:
Flash: Auto / Red eye / Force on / Slow sync / Force off
Macro: Off / On
SET/DISP: OSD on / Guide line / OSD off
Button
Stabilizer: Off / On
Resolution: 12M / 3:2 / 16:9 / 8M / 4M / 2M / VGA
Drive Mode: Off / 2 sec. / 10 sec. / Double / Burst
Face Tracking: Off / On
Photo Frame: 10 frames can be selected
Beep: Off / On
Menu
Auto Review: Off / 1 sec. / 3 sec. / 5 sec.
Rest of settings will not be controlled as below:
y Quality: S.Fine y Highlight: Off
y Metering: Multi y Sharpness: Normal
y White balance: Auto y Effect: Off
y ISO: Auto y Date Stamp: Date & Time
y Exposure: Auto y Digital Zoom: Off
Fixed setting
(*)
y AEB: Off y AF lamp: Auto
y Shutter sound y File No.
y Start-up sound y TV out
y Power save y USB
y Date & Time y Start-up image
Utility setting
(**)
y Language
(*)Fixed setting: Settings are fixed in Q mode.
(**)Utility setting: Use the same setting as last mode used.
AgfaPhoto DC-2030m
27
Setting Image Size and Quality
You can select lower image resolution and quality to decrease the image size to capture
more images. Choose a suitable setting according to the desired image quality and
purpose. For details, see page 16.
Resolution Values
Image Size Print Size
4000 x 3000 Printing larger than A4-size.
4000 x 2664
4000 x 2248
3264 x 2448
2272x 1704
1600 x 1200
640 x 480
Printing to postcards or attaching to e-mail.
Larger
Smaller
Quality Values
Compression Purpose
Super Fine
Shoot higher quality images.
Fine Shoot normal quality images.
Normal Shoot for more images.
Higher Quality
Lower Quality
AgfaPhoto DC-2030m
28
Using the Zoom Function
Your camera has a combination of optical and digital zoom functions that allows you to
zoom in on far away subjects or zoom out for a wide angle shot.
The optical zoom is achieved by mechanically adjusting the lens of the camera. The
digital zoom enlarges or shrinks the image using a software process.
Select the zoom setting, and
point the camera at the subject.
Press the zoom button (n) to
compose the image.
[W]: zoom out for a wide-angle
shot.
[T]: zoom in for a telephoto shot.
y When the zoom button is
pressed, the zoom bar appears
on the LCD monitor.
y When the optical zoom (o)
factor is at maximum, zooming
stops temporarily. Press the
[T] again, the camera switches
to the digital zoom (p)
automatically and zooming
continues.
y The digital zoom (p) will not
activate in movie recording.
Press shutter button to take a
picture.
y Digital zoom works by enlarging the center portion of an image through a
software interpolation process.
y The digital zoom is used to achieve magnification levels up to approx. 4 times.
1
2
3
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
29
Using the Flash
The flash is not only for taking pictures when there is insufficient light, but also when the
subject is in shade or in backlight conditions. Press the flash button to cycle your camera
through the various flash modes. The flash will not activate when continuous shooting or
movie recording.
Turn the power on, and set the camera
to the REC mode (
page 13).
Press the flash button (n) to change
the flash mode.
y Each time the flash button is
pressed, the flash icon (o) changes.
Auto flash:
Flash fires automatically when
shooting conditions require extra
lighting.
Red-eye reduction:
Flash strobes to let the subject’s
eyes adjust to the flash, then
fires again to take the actual
image. Your camera will detect
the subject brightness and use
the flash only when required.
Force on:
Flash fires every time you take a photo, regardless of lighting conditions.
Slow sync:
Flash fires with a slow shutter speed.
Force off:
The flash never fires even in dark situation.
Press shutter button to take a picture.
1
2
3
AgfaPhoto DC-2030m
30
y The flash charging time may increase when the battery is low.
y The available flash settings are limited depending on the REC mode you selected
Using the Macro
Your camera is equipped with a macro function that allows you to focus on very close
subjects. In macro mode you can focus on subjects 10 cm from the lens when in the
maximum wide angle setting and 40 cm in the maximum telephoto setting.
Turn the power on, and set the
camera to the REC mode
(
page 13).
Press the macro button (n)
enters the macro mode.
y The macro icon (o) displays in
the LCD monitor.
y To leave the macro mode,
press the macro button (n)
again.
Pan Focus:
When Pan Focus is set, the
camera focuses on every
object.
Infinity:
When Infinity is set, the
camera focuses on distant
objects.
Press shutter button to take a
picture.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
2
3
AgfaPhoto DC-2030m
31
y Distances referred to measure the distance between the camera lens surface
and the subject.
y The available macro settings are limited depending on the REC mode you
selected.
Using the Self-timer & Burst
Use the self-timer to set a delay from the time the shutter button is pressed to the time
the image is shot. Use the burst to record continuous still images shooting.
Turn the power on, and set the
camera to the REC mode
(
page 13).
Open the REC menu (
page 16).
y Use
or to select [Drive
mode] from the REC menu.
Change the setting.
y Press
or to select a drive
mode, then press the SET
button.
Off:
Record a single image.
2 sec.:
The shutter release will be delay for 2 seconds.
10 sec.:
The shutter release will be delay for 10 seconds.
Double:
Record two images in a shot after pressing the shutter release button 10
and 12 seconds.
Burst:
1
2
3
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
32
Keep pressing the shutter button fully to take continuous shooting.
Release the shutter button to stop shooting.
Press shutter button to take a picture.
y When using the self-timer function, be sure to use a tripod or place the digital
camera on a level, stable surface.
Using the Aperture Priority
In this mode, you can set an aperture value to match the brightness. A higher aperture
value brings the background out of focus. Selecting a lower aperture value allows you to
soften the background.
Turn the power on, and set the
camera to the Aperture Priority
(
page 14).
Adjust the aperture value by
pressing
or button.
Press shutter button to take a
picture.
y The larger the aperture value the smaller the lens opening, allowing less light to
enter the camera.
4
T
T
i
i
p
p
s
s
1
2
3
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
33
Using the Shutter Priority
In this mode, you can set a shutter speed to match the brightness. Faster shutter speeds
allow you to take a sharp picture of a moving subject while slower speeds create a trail
effect and allow you to shoot without a flash in dark areas.
Turn the power on, and set the
camera to the Shutter Priority
(
page 13).
Adjust the shutter speed by
pressing
or button.
Press shutter button to take a
picture.
Using the Manual Exposure
You can manually set the shutter speed and aperture to achieve a particular effect.
Turn the power on, and set the
camera to the Manual Exposure
(
page 14).
2
Use the SET button to switch
between aperture value and
shutter speed control. Press
or to adjust the setting.
Press shutter button to take a
picture.
y Press the shutter button halfway,
the difference between the
standard exposure and the
selected exposure appears in
red.
1
2
3
1
3
2
AgfaPhoto DC-2030m
34
Using the Stabilizer
With more sensibility and faster shutter speed to bright up the pictures, effectively
prevent blur image caused by hand shack or target movement.
Recording Movie Clips
Turn the power on, and set the
camera to the Movie mode
(
page 13).
Compose the subject on the
monitor.
y Aim the focus area (q) to the
subject that you want to take.
y The LCD monitor displays the
available recording time (p).
Start recording.
y Press the shutter button (n) to
start recording.
y Using the zoom button (o) to
adjust the image size.
y The White Balance is set and
locked to the settings of the first
frame
1
2
3
AgfaPhoto DC-2030m
35
Finish recording.
y Press the shutter again to end recording.
y The camera will stop recording automatically when the memory capacity
has been reached.
y Sound cannot be recorded while pressing the zoom button..
y The digital zoom cannot be used in Movie mode.
y When the maximum capacity for a single video has been reached, simple press
the shutter button again to continue recording. The camera will automatically stop
recording when the memory capacity is full.
Setting the Movie Size
Movie Size and Frame Rate
Icon Resolution Frame Rate
640 x 480
320 x 240
640 x 480 ( YouTube®)
30 frames/ sec.
YouTube® Mode
The YouTube® Mode allows you to record movies with predefined video settings for
easy upload to the YouTube® website.
YouTube® supports two file upload standards:
y Single File Uploader. The maximum movie file size is up to 100 MB.
y YouTube® Uploader. The maximum movie file size is up to 1 GB.
Most uploaded movie length ranges within 5 minutes, although you can upload a
maximum movie length of 10 minutes.
Therefore when you record using the YouTube® mode, the following standards
are followed:
1
2
C
C
a
a
u
u
t
t
i
i
o
o
n
n
4
AgfaPhoto DC-2030m
36
y Recorded movies are set to YouTube® standard resolution of 640 X 480.
y Recording automatically stops when the file reaches 100 MB.
y Using VLC software to play videos of the MAC may lead to display issues. We
recommend using the QT player for video playback.
y To record a YouTube® movie, select
from the Movie Size function.
Recording Audio Clips
Turn the power on, and set the camera to the Voice REC mode
(
page 13).
Press the shutter button to start recording.
y The voices are recorded from the microphone of the camera. Be careful to
avoid touching the microphone while recording.
Press the shutter button again to end recording.
y The camera will stop recording automatically when the memory capacity
has been reached.
Playing Back Audio Clips
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Press
or to select the
audio clip that you want to
playback.
Start playing back.
3
1
2
3
1
2
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
37
y Press to start playing the audio clip.
y Press
to stop the audio clip, or press to pause it. When audio clip
paused, press
again to resume.
Recording a Voice Memo
You can add a voice memo to the still images after you record it.
Turn the power on, and set the
camera to the PLAYBACK mode
(
page 13).
Press
or to select a still
image that you want to add a
voice memo to.
y If the image already has the
voice memo recorded, the
appears on the LCD monitor.
The new recording will replace
the previous one.
Open the PLAYBACK menu.
y Press the MENU button, using four-way control to select Voice Memo (
)
and press the SET button.
Press the SET button to start recording for 30 seconds.
y Press the SET button again to end recording.
y The voice memo cannot be added to a movie clip or a protected image.
y You cannot delete only the voice memo. When you delete the image, the
attached voice memo is also deleted.
3
1
2
4
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
38
Playing Back a Voice Memo
Turn the power on, and set the camera to the PLAY mode ( page 13).
Press
or to select the image that has the voice memo recorded.
Start playing back.
y Press
to start playing the voice memo.
y Press
to stop the voice memo, or press to pause it. When voice
memo paused, press
again to resume.
Other Recording Functions
Setting the Metering
There are 3 different light metering options available on your camera.
Option Description
Light is measured from the entire shooting screen, but gives
more importance to the values near the center.
Selects an exposure based on readings from multiple points in
the subject area.
Selects an exposure based on a single reading taken from the
center of your picture.
Setting the White Balance
Adjust the white balance to match different light sources such as sunlight, incandescent
(tungsten) lighting or, fluorescent lighting.
Option Description
Automatically corrects white balance. Ideal for general
photography.
Adjusts for bright sun conditions, or natural light conditions.
Adjusts for cloudy days or twilight conditions.
3
2
1
AgfaPhoto DC-2030m
39
Adjusts for normal indoor lighting conditions. Corrects the
orange hue of household light bulbs. Ideal for indoor photos
under tungsten or halogen lighting without a flash.
Adjusts for fluorescent lighting. Corrects the green hue of
fluorescent lighting. Ideal for indoor photos under fluorescent
lighting without a flash.
For more accurate adjustment or when the light source cannot
be specified.
y Point the camera at a white piece of paper or similar object under the lighting
conditions for which you want to set the white balance, and then press the
Shutter button.
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
40
Setting the ISO
With the initial settings, the ISO sensitivity is automatically set according to the
brightness of the subject.
Option Description
Auto Sets the ISO sensitivity automatically.
ISO 125 Sets the sensitivity to ISO 125 equivalent.
ISO 200 Sets the sensitivity to ISO 200 equivalent.
ISO 400 Sets the sensitivity to ISO 400 equivalent.
ISO 800 Sets the sensitivity to ISO 800 equivalent.
ISO 1600 Sets the sensitivity to ISO 1600 equivalent.
ISO 3200 Sets the sensitivity to ISO 3200 equivalent.
y Higher ISO speeds increase the image noise. To take clean images, use as low
an ISO speed as possible.
Setting the Exposure
Set the exposure value manually to compensate for unusual lighting conditions such as
indirect indoor lighting, dark backgrounds, and strong backlighting.
Setting the AEB
Sets the auto exposure bracketing (AEB) to shoot 3 continuous images, each with a
different exposure setting: correctly exposed, underexposed, and overexposed.
Setting the Highlight
Make the subject stand out from its surroundings. The subject will be in focus in three
different ranges:
/ /
y The Photo Frame and Face Tracking cannot be used as using the Highlight.
T
T
i
i
p
p
s
s
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
41
Setting the Sharpness
You can select whether you want the image to have sharp or soft outlines.
Option Description
The edges of the image are emphasized. The edges will
become sharp, but noise may occur in the recording image.
The edges of the image are sharp. This is suitable for printing.
The edges of the image are softened. This is suitable for editing
images on PC.
Setting the Photo Effect
You can add special effects to your images in Record mode or in Playback mode.
Option Description
Off No effect is added to the image.
Red eye removal. (Playback only)
B&W Convert image to black & white.
Sepia Recorded image will be stored in a sepia tone.
Negative Opposite what they were in the original image. (Playback only)
Mosaic Add mosaic tiles to the images. (Playback only)
Red The image becomes reddish.
Green The image becomes greenish.
Blue The image becomes bluish.
Setting Date Stamp
The Date Stamp function can be used to add a date to your pictures as you take them.
Option Description
Off Do not add the recorded date & time to printed images.
Date Only add the recorded date to printed images.
Date & Time Add the recorded date & time to printed images.
AgfaPhoto DC-2030m
42
Setting Face tracking
After initializing the face tracking function, the lens will lock the main character in the
picture and follow their movements. Also, the use of auto digital zoom technology allows
the lens to extend and retract.
y Pressing the shutter halfway showing green AF area means focus is complete.
y Face tracking is powered by Arcsoft.
y Under some environmental influences, face tracking function may be limited.
y The Highlight and Photo Frame cannot be used as using the Face Tracking.
y When capturing an image with several faces, face tracking function will take up
more time tracking faces for the first time
Setting Photo Frame
You can add 10 kinds of frames to still images, making them more interesting.
y This feature is only available with still images (except 3:2 and 16:9).
y The Highlight and Face Tracking cannot be used as when using the Photo Frame.
Setting AF Lamp
The AF Lamp function allows you record images in low light conditions.
Option Description
Off Disable the AF lamp while recording images.
Auto
The AF lamp turns on automatically by half pressing the shutter
button under low light conditions.
T
T
i
i
p
p
s
s
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
43
Playback
Playing Back Images
Turn the power on, and set
the camera to the PLAYBACK
mode (
page 13).
y The latest recorded image
appears on the LCD
monitor.
y If there are no images
stored, a message [No
image] appears.
Press the four-way control
or (n).
y
: displays the previous image.
y
: displays the next image.
y Holding down
or scrolls images in a high speed.
Playing Back Movie Clips
Turn the power on, and set the camera to the PLAYBACK mode
(
page 13).
Press
or to select a movie clip that you want to playback.
Start playing back.
y Press
to start playing the movie clip.
y Press
to stop the movie clip, or press to pause it. When the movie
paused, press
again to resume.
3
2
1
1
2
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
44
y During movie playing back, press
to fast forward or press to rewind it.
y Press the shutter to capture the still image from the movie clip while it had paused.
Magnifying & Trimming Still Images
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Select an image.
y Press
or (p) to select
the image that you want to
magnify or trimming.
y Only still images can be
magnified and trimmed.
y
Magnify the image.
y Press [T] (n) to magnify the image and the central portion of the image is
displayed. You can use the arrow button (p) to view different parts of the
magnified image.
y Press the MENU button (o) to return to the normal size.
Trim the image.
y Press the SET button (p) to set the image trimming.
Save the image.
y Press the SET button (p) again to trim the selected image and save it as a
new one.
T
T
i
i
p
p
s
s
3
5
4
1
2
AgfaPhoto DC-2030m
45
Viewing in Thumbnail
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Press the zoom button [W], a
thumbnail screen is displayed.
Use the four-way control to select the desired image, and press [T] or the
SET button to show the selected image in full screen.
y You can protect or delete multiple images in thumbnail, see page 47, 49.
Playing a Slide Show
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Enter the slide show.
y Press the MENU button (n),
use the four-way control (o)
to select Slide Show (
)
and press the SET button
(o).
Change the slide show settings.
y Use the four-way control (o) to set the slideshow interval (
), effect ( )
and repeat (
).
y You can set the interval between 1~10 seconds.
3
1
2
T
T
i
i
p
p
s
s
1
2
3
AgfaPhoto DC-2030m
46
Playing the slide show.
y Press the SET button (o) to start the slideshow.
y During the slideshow, press the SET button (o) to pause the slideshow and
press the SET button again to resume.
Deleting Files
Deleting a Single File
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Open the menu.
y Press the MENU button (n),
then use the four-way control
(o) to select Delete (
)
and press the SET button
(o).
Press
or (o) to select [SINGLE], and then press the SET button (o).
Press
or (o) to select the image you want to delete.
Press the SET button (o) to delete the image.
y Repeat step 4~5 to delete images.
y To quickly delete the current display image
1. Select the image you want to delete.
2. Press the Delete button (p) to show a confirmation.
3. Press the SET button (o) to delete the current display image.
y Protected images cannot be deleted with this function.
4
1
2
3
4
5
T
T
i
i
p
p
s
s
AgfaPhoto DC-2030m
47
Deleting Multiple Files
Turn the power on, and set the
camera to the thumbnail screen
(
page 45).
Open the menu.
y Press the MENU button, then
Press
or to select to
select Delete (
) and
press the SET button.
Press
or to select [Select], and then press the SET button.
y The frame of the selected image turns green.
Select multiple images.
y Use the four-way control to select the image.
y Press the SET button toggles the
on and off. Repeat this step until all
images that you want to delete are displayed with an icon
.
Delete images.
y Press the MENU button, then select [Yes] and press the SET button. All
selected images will be deleted.
y To cancel delete, press the MENU button in this step.
1
2
3
4
5
AgfaPhoto DC-2030m
48
Deleting All Files
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Open the menu.
y Press the MENU button, then
use the four-way control to
select Delete (
)
and press the SET button.
y You can open the menu in full screen or in thumbnail.
Press
or to select [ALL], and then press the SET button.
Press the SET button to delete all unprotected images.
Protecting a Single File
Turn the power on, and set the camera to the PLAYBACK mode
(
page 13).
Open the menu.
y Press the MENU button, then use the four-way control to select Protect
(
) and press the SET button.
Press
or to select [SINGLE], and then press the SET button.
Press
or to select the image you want to protect.
Press the SET button to protect the image.
y When the file is locked, the
displays on the LCD monitor.
y Repeat step 4~5 to protect images.
y To unlock the file, press the SET button again in step 5. The
will
disappear and the file is unlocked.
1
2
3
4
5
3
1
2
4
AgfaPhoto DC-2030m
49
Protecting All Files
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Open the menu.
y Press the MENU button, then
use the four-way control to
select Protect (
) and
press the SET button.
y You can open the menu in full
screen or in thumbnail.
Press
or to select [Lock all], and then press the SET button.
y To unlock all files, select [Unlock all] in this step, then press the SET
button.
Press the SET button to protect all images.
Protecting Multiple Files
Turn the power on, and set the
camera to the thumbnail screen
(
page 45).
Open the menu.
y Press the MENU button, then
Press
or to select to
select Protect (
) and
press the SET button.
Press
or to select [Select], and then press the SET button.
y The frame of the selected image turns green.
1
2
3
3
1
2
4
AgfaPhoto DC-2030m
50
Select multiple images.
y Use the four-way control to select the image.
y Press the SET button toggles the
on and off. Repeat this step until all
images that you want to protect are displayed with an icon
.
Protect images.
y Press the MENU button, then select [Yes] and press the SET button. All
selected images will be protected.
y To cancel protect, press the MENU button in this step.
Editing Images
Rotating Still Images
Turn the power on, and set the
camera to the PLAYBACK
mode (
page 13).
Press
or to select the
image you want to rotate.
Open the menu.
y Press the MENU button, then use the four-way control to select Rotate (
)
and press the SET button.
Press the SET button to rotate the image.
y Each press rotates the image 90 degrees in clockwise.
Press
or to select OK, and then press the SET button to finish
rotating.
4
5
3
1
2
4
5
AgfaPhoto DC-2030m
51
Changing the Image Size
Turn the power on, and set the camera to the PLAYBACK mode
(
page 13).
Press
or to select the image you want to resize.
Open the menu.
y Press the MENU button, then use the four-way control to select Resize
(
) and press the SET button.
Press
or to select an option, and then press the SET button.
y The resized image will be saved as a new file.
y Only a large size image can be resize to a smaller one.
Changing the Image with Effects
You may use Red Eye Removal remove the red eye caused by flash from original photo.
Or use color filters to save as a new image.
Turn the power on, and set the camera to the PLAYBACK mode
(
page 13).
Press
or to select the image you want to add the effect.
Open the menu.
y Press the MENU button, then use the four-way control to select Photo Edit
(
) and press the SET button.
Press
or to select an option, and then press the SET button.
y The edited image will be saved as a new file.
1
2
3
4
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
2
3
4
AgfaPhoto DC-2030m
52
Choosing the Image with Photo Frame
Turn the power on, and set the camera to the PLAYBACK mode
(
page 13).
Press
or to select the image you want to add the photo frame.
Open the menu.
y Press the MENU button, then use the four-way control to select Photo
Fames (
) and press the SET button.
Press
or to select the image you want, then press the SET button to
apply the choice.
y The edited image will be saved as a new file.
3
4
2
1
AgfaPhoto DC-2030m
53
Copying the Files
You may copy the data from the camera’s internal memory to the memory card for
convenience.
Be sure you have inserted a
memory card into your digital
camera. Set the camera to the
PLAYBACK mode.
(
page 13).
Open the menu.
y Press the MENU button, then
use the four-way control to
select Copy to card (
)
and press the SET button.
Press or to select [Single], then press the SET button.
y To copy all images to a memory card, select [All].
Press
or to select the image you want to copy to a card.
Select [Yes] and then press the SET button to start copy.
y Repeat step 4~5 to copy other images.
y Press the MENU button to complete the setting.
3
1
2
4
5
AgfaPhoto DC-2030m
54
Setting the DPOF
The Digital Print Order Format (DPOF) setting allows you to select images on the
memory card for printing and specify the number of print copies in advance using the
camera. This is extremely convenient for sending the images to a photo developing
service or for printing on a direct print function compatible printer.
Turn the power on, and set the
camera to the PLAYBACK mode
(
page 13).
Open the menu.
y Press the MENU button, then
use the four-way control to
select DPOF (
) and press
the SET button.
s
Press
or to select [Single], then press the SET button.
y To set the DPOF setting for all images, select [All] in this step.
y To reset all DPOF settings to initial default, select [Reset] in this step.
Press
or to select the image you want to print out.
Set the number of copies.
y Press
or to specify the number of copies.
y The number of copies can be set from 0 to 30.
y To cancel this image DPOF setting, set the number of copies to 0.
Print the date stamp out.
y Press SCN button to set the date stamp of current image. Press SCN button
again to turn off date stamp.
y Repeat step 4~6 to other images for printing.
After you finished all image settings, press the SET or MENU button to
apply it.
3
1
2
6
7
4
5
AgfaPhoto DC-2030m
55
Choosing a Startup Image
Turn the power on, and set the camera to the PLAYBACK mode
(
page 13).
Open the menu.
y Press the MENU button, then use the four-way control to select Start-up
Image (
) and press the SET button.
Press
or to select the image you want, then press the SET button to
apply the choice.
y A message “Completed” appears.
Set the camera to the Setup Menu (
page 17).
Press
or to select
Start-up Image (
) then
press
or the SET button.
Press
or to select a
desired option and press the
SET button to apply the setting.
[Off]: Disable the start-up image.
[System]: Use camera default image.
[My image]: Use the image that you just specified in step 3.
Press the MENU button to close the menu.
y The start-up image will not be deleted even if the original image is deleted or
memory formatted.
3
1
2
4
5
6
7
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
56
Making Connections
Connecting the Camera to a TV
You can display recorded images on a television with a supplied AV cable.
Set the TV out to match the TV system that you are using (
page 19).
Turn off the camera and the TV.
Use the supplied AV cable to connect the camera to the TV set.
Set the TV input signal to Video In.
y Refer to the documentation included with your TV for more information.
Display on TV.
y Everything that would normally appear on the camera’s LCD screen, such
as photo and video clip playback, slide shows, and image or video capture,
appears on the TV.
3
1
2
4
5
AgfaPhoto DC-2030m
57
Connecting the Camera to a PC
There are two ways to download files from the camera’s internal memory or memory
card to a computer:
y Inserting the memory card into a card reader
y Connecting the camera to a computer using the supplied USB cable
Using the Card Reader
Eject the memory card from the
camera and insert it in a card reader
that is connected to a computer.
Open [My Computer] or [Windows
Explorer] and double-click the
removable drive icon that represents
the memory card.
Copy images from the card into a directory of your choice on the
computers hard disk.
Connecting the Camera to a Computer with the USB Cable
Install the USB software driver
included with the bundled CD-ROM.
Connect the supplied USB cable to
the computers USB port and turn on
the camera.
y The LCD screen turns off when the
connection to the computer has
been successfully completed.
Open [My Computer] or [Windows Explorer]. A “Removable Disk” appears
in the drive list.
Double-click the “Removable Disk” icon to view its contents.
y Files stored on camera are located in the folder name “DCIM”.
3
1
2
3
1
2
4
AgfaPhoto DC-2030m
58
Appendix
About the Folder & File Name
Your digital camera automatically creates a directory of folders in the internal memory or
memory card that it uses to organize still images, movie clips and other information.
Folder Structure
Your camera creates three directory
names:
y DICAM. All captured images, videos and
audio files are stored in this folder except
for files recorded using the Auction or
YouTube® mode.
y _AUCT. Captured images using the
Auction mode are saved in this folder.
y _UTUBE. Captured videos using the
YouTube® mode are saved in this folder.
Folder name begins with a 3-digit number
from 100 to 999 and followed by “DICAM”
or “_AUCT” or “UTUBE”, each folder holds
up to 9999 files. If new files are made, a
new folder named in sequence will be
made automatically.
AgfaPhoto DC-2030m
59
File Naming
File name begins with “DSCI” and are followed by a 4-digit number that increases in
sequence. File numbering starts from 0001 when a new folder is created.
If the highest folder number is 999 and highest file number exceeds 9999, the camera
will display the warning message “Folder cannot be created”. When it appears, try one of
the following ways:
y Reset the file number and plug in a new memory card.
y The folder number and file number are initialized and renumbered from 100 and
0001 respectively.
y Do not change the folder and file names in the memory card using your
computer. It may be unable to playback the data using the digital camera.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
AgfaPhoto DC-2030m
60
Troubleshooting
Problem Cause Solution
Battery is inserted in the wrong
direction.
Reload battery in the correct
direction.
Batteries are dead. Replace or recharge batteries.
Power does not turn on.
The battery compartment door
is open.
Make sure the battery compartment
door is securely closed.
The flash is charging. Wait for the flash to charge.
Memory is full. Insert a new memory card.
The camera does not
take pictures.
Memory card is not formatted
correctly.
The card may be defective, use a
new card.
The Flash is charge. Wait for the flash to charge. Image is not recorded
when the shutter button
is pressed.
Memory is full. Insert a new memory card.
The flash does not fire. Flash is set to OFF. Set the flash to any mode except off.
The camera was moving when
the image was captured.
Hold the camera steady when
shooting picture.
Image is blurry or out of
focus.
The subject was beyond the
range within which the camera
can focus.
Turn the Macro mode on it the
subject is within 10 cm or 40 cm.
Do not use Macro mode when
shooting distant subjects.
Image is not displayed
on the LCD monitor.
A memory card with non-DCIF
images (recorded with other
camera) is loaded.
This camera cannot display
non-DCIF images.
Recorded images are
not saved in memory.
The camera was turned off /
powered down before the
image was stored in memory.
If the battery low indicator appears
on the LCD monitor, replace the
battery immediately.
Cannot transfer images
to a computer after
connecting the USB
cable.
USB driver is not installed. Install the USB driver before you
connect the camera to a computer /
turn the camera on.
Card error The memory card format may
not be correct.
Re-format the memory card to the
FAT format using a card reader in
Windows.
The lens got stuck up. The type of the battery used
may be incorrect or the battery
power level is too low.
Do not force the lens to go back.
Change the battery or charge the
battery before using the camera.
AgfaPhoto DC-2030m
61
Specifications
Sensor 12 megapixel CCD, Size : 1/2.3 inch
Lens Focal length : f = 6.3 ( W ) ~ 18.9 ( T ) mm, 3X optical zoom, 4X
digital zoom
LCD Display 2.7” LCD
Focus Range Normal: 0.4m ~ Infinity (All Zoom Step) / 0.1m ~ Infinity (at Wide
only); Macro: (W) 10 cm ~ 80 cm / (T) 40 cm ~ 80 cm
Aperture F/ 3.1 ( W ), 5.6 ( T )
Shutter 8 ~ 1/2000 sec.
File Format Still Image: EXIF 2.2 compatible format ( JPEG compression ),
DCF compatible. Support DPOF, Video: AVI; Audio: WAV
Resolution Still Image: 4000 x 3000 (12M) / 4000 x 2664 (3:2) / 4000 x 2248
(16:9) / 3264 x 2448 (8M) / 2272x 1704 (4M) / 1600 x 1200 (2M) /
640 x 480 (VGA); Video: 640 x 480 / 320 x 240
Scene Mode
Program / Movie / Voice REC / Q. Mode / Portrait / Landscape /
Sunset / Backlight / Smile Capture / Kids / Night scene / Fireworks /
Snow /Sports / Party / Candlelight / Night Portrait / Soft Skin / Soft
Flowing Water / Food / Building / Text / Auction / Blink Detection /
Intelligent Scene / Aperture Priority / Shutter Priority / Manual
Exposure
Sensitivity Auto / ISO 125 / ISO 200 / ISO 400 / ISO 800 / ISO 1600 / ISO 3200
White Balance Auto / Daylight / Cloudy / Tungsten / Fluorescent (H) / Fluorescent
(L) / Custom
Exposure Control -2EV to +2EV in 1/3 step
Metering Center-weighted / Multi / Spot
Drive mode 2 sec. / 10 sec. / Double / Burst
Flash Auto / Red eye reduction / Always on / Slow sync / Always off
Photo Edit Red eye removal / Black & White / Sepia / Negative / Mosaic / Red /
Green / Blue
Storage 32 MB internal memory / SD Card (2 GB) / SDHC (16 GB)
TV system NTSC / PAL
Power Supply AA alkaline battery X2 (Use alkaline batteries or rechargeable
batteries only)
Ambient
temperature
Operating: 0° C to 50° C, Storage: -20 to 60° C
AgfaPhoto DC-2030m
62
Microphone Built-in
Speaker Built-in
Dimension
Camera Body ( W x H x T ):
92 x 60.5 x 24.3 mm
Weight Camera Body w/o battery : Approx. 115 (g)
*These specifications are subject to change without notice.
AgfaPhoto DC-2030m
63
Customer care
More information on the complete AgfaPhoto digital camera product range can be found
under www.plawa.com / www.plawausa.com.
To return a product, you will need an RMA number which must be clearly visible on the
returned shipment. You can find further information on the return of goods either by phoning
our Support Hotlines or via the plawa website under the Menu item "Service & Support".
Service & Repair (USA/ Canada):
1-866 475 2605
www.plawausa.com
Support Service (USA/ Canada)
support-apdc@plawausa.com
Service & Repair Hotline (EU):
00800 752 921 00 (from a landline only)
Service & Support Hotline (Germany):
0900 1000 042 (1.49 Euro/ min. from a German landline only)
Online Service / International contact (Not for USA/ Canada):
support-apdc@plawa.com
Manufactured by
plawa-feinwerktechnik GmbH & Co. KG
Bleichereistraße 18
73066 Uhingen
Germany
AgfaPhoto is used under license of Agfa-Gevaert NV & Co. KG or Agfa-Gevaert NV.
Neither Agfa-Gevaert NV & Co KG nor Agfa-Gevaert NV manufacture this product or
provide any product warranty or support. For service, support and warranty information,
contact the distributor or manufacturer.
AgfaPhoto DC-2030m
64
Copyright
This manual contains proprietary information protected by copyright. All rights are reserved. No
part of this manual may be reproduced by any mechanical, electronic or other means, in any
form, without prior written permission of the manufacturer. © Copyright 2008.
Trademark Recognition
Windows 98, 2000, ME, XP are registered trademarks of Microsoft Corporation in the United
States and/or other countries. Windows is an abbreviated term referring to the Microsoft
Windows Operation System. All other companies or product names are trademarks or
registered trademarks of their respective companies. YouTube is a brand of Google, Inc. And
YouTube, LLC, Mountain View, California, US.
Disposal of Waste Equipment by Users in Private Households in
the European Union
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose of
your waste equipment by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. The separate collection and recycling of your
waste equipment at the time of disposal will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or the shop where you
purchased the product.
FCC Compliance and Advisory
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: 1.) this device may not cause harmful interference, and 2.) this device must
accept any interference received, including interference that may cause unsatisfactory
operation. This equipment has been tested and found to comply with the limits for a Class
B peripheral, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
AgfaPhoto DC-2030m
65
communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. When shielded
interface cables have been provided with the product or when specified additional
components or accessories have elsewhere been designated to be used with the
installation of the product, they must be used in order to ensure compliance with FCC
regulations.
Declaration of Conformity
We herewith confirm the following designated product: AgfaPhoto digital camera
DC-2030m has been tested and found to comply with the requirements set up in the council
directive on the approximation of the law of members’ states relating to the EMC Directive
2004/108/EC. For the evaluation regarding to the electromagnet compatibility, the following
standards were applied:
EN 55022: 2006 Class B
EN 55024: 1998+A1: 2001+A2: 2003
EN 61000-3-2: 2006
EN 61000-3-2: 1995 + A1: 2001 + A2: 2005
IEC 61000-4-2: Edition 1.2: 2001-04
IEC 61000-4-3 Edition 3.0: 2006
IEC 61000-4-4 2004
IEC 61000-4-5 Edition 2.0: 2005
IEC 61000-4-6: Edition 2.2: 2006
IEC 61000-4-8 Edition 1.1: 2001-03
IEC 61000-4-11 Second Edition: 2004
AS/NZS CISPR 22:2006
The device is marked with CE logo.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Agfaphoto dc 2030m bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Agfaphoto dc 2030m in de taal/talen: Engels als bijlage per email.

De handleiding is 5,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Agfaphoto dc 2030m

Agfaphoto dc 2030m Gebruiksaanwijzing - Deutsch - 78 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info