587610
58
Verklein
Vergroot
Pagina terug
1/184
Pagina verder
58
EN
IMDCFJ. 12.05 6343841_03
Setting heating FORCE-OFF
Index - String
MIN
value
MAX
value
Parameter function
30 °C 70 °C
The heat pumps check the working temperature (input or output), to which a safety threshold is con-
nected, and beyond which the compressor is switched off immediately and automatically; this threshold
is called FORCE-OFF.
Setting the safety threshold
Index - String
MIN
value
MAX
value
Parameter function
0,5 °C 20 °C
Temperature threshold above the force-off, which reactivates the start-up of the compressor after the
switching off for force-off.
Setting integral time
Index - String
MIN
value
MAX
value
Parameter function
0 s 999 s
The units possess an advanced logic for controlling the processed water temperature; the complete
check prevents the system arriving at a point of equilibrium at a higher or lower temperature compared
with the one set in the work setting. Remember that an increase in the integration time weakens the
effect of the integral control.
Setting derivation time
Index - String
MIN
value
MAX
value
Parameter function
0 s 120 s
Time within which the input water temperature is checked to estimate the load on the system; if the
band on the setting value is exceeded within this time, the unit will be activated.
Setting the anti-freeze threshold
Index - String
MIN
value
MAX
value
Parameter function
-50 °C 20 °C
In the units it is possible to set a threshold for the anti-freeze alarm; this value specifies at what tempe-
rature the anti-freeze alarm is activated. Remember that, to modify the anti-freeze threshold parameter,
the corresponding dip-switch must be activated (see the dip-switch configuration table).
Setting frost protection
Index - String
MIN
value
MAX
value
Parameter function
04
In the units, it is possible to set a safety control on the water output temperature; on the basis of the
value assigned to this parameter, the anti-freeze electric heater is managed as follows:
• value 0, anti-freeze electric heater absent;
• value 1, anti-freeze electric heater installed and working only with machine in heat or cool mode;
• value 2, anti-freeze electric heater installed and working also in standby, but switching on the pump;
• value 3, anti-freeze electric heater working in standby without the pump being activated;
• value 4, with external air temperature less than 3°C, the pump is activated for 2 minutes every 30, to
monitor the temperature of the water throughout the system.
Parameters only visible in heat pump models
Parameters only visible in models set for
hot domestic water productio
Parameters only visible in the models with DCP installed
Parameters only visible in bicompressor models
Parameters only visible in the models with inverter compressor
58

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Aermec MODUCONTROL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Aermec MODUCONTROL in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info