Handleiding Aeris A300 CS (pagina 54 van 64) (Engels)

618071

Verklein

Vergroot

Pagina terug

1/64

Pagina verder

A300 CS OPERATING MANUAL

BATTERY REPLACEMENT

The procedures that follow must be closely adhered to to avoid entrance of water into the unit. Dam-

age due to improper Battery replacement (or subsequent leakage of moisture into the unit) is not

covered by the A300 CS's 2 year warranty.

The Battery Compartment should only be opened in a dry and clean environment with extreme care taken to prevent the entrance

of moisture or dust.

As an additional precautionary measure to prevent formation of moisture in the Battery Compartment, it is recommended that the

Battery be changed in an environment equivalent to the local outdoor temperature and humidity (e.g., do not change the Battery

in an air conditioned environment then take it outside during a hot sunny day).

Inspect the Buttons, Lens, and Housing to ensure they are not cracked or damaged. If there is any sign of moisture inside the unit,

DO NOT attempt to use it for diving until it receives proper service by the AERIS factory or an Authorized Regional Facility.

Data Retention (calculations & settings)

When the battery is removed, settings* and calculations for repetitive dives are retained in volatile memory until a new battery is

installed.

*Date will have to be set, Time may require adjustment for the time duration that the battery remains out of the unit.

After the Battery is replaced during a 24 hour period after dives, a screen displaying the graphics DATA SAVED CALIBRATE

COMPASS displayed for 3 seconds (Fig. 96) that will then switch to the Compass Calibrate Face Down screen.

> Calibrate the Compass.

Refer to page 45.

> Verify all Set points prior to diving.

BATTERY REMOVAL

Locate the Battery Cover on the end of the housing:

• Apply a coin to the recessed slot of the Cover and turn it counter clockwise out of the housing (Fig. 97).

• Remove the Battery and discard it according to local regulations governing disposal of Lithium batteries.

INSPECTION

• Closely check all of the sealing surfaces for any signs of damage that might impair proper sealing.

• Inspect the Buttons, Lens, and Housing to ensure they are not cracked or damaged.

• Remove the Battery Cover O-ring and inspect it for any signs of deterioration or deformity. DO NOT use tools to remove the

O-ring.

• To ensure proper sealing, O-ring replacement is highly recommended each time the Battery is replaced.

• Closely examine the Battery Cover and Housing for any signs of damage that might prevent proper threading.

• Closely examine the inside of the Battery Compartment for any signs of corrosion indicating entrance of moisture into the

unit.

WARNING: If damage, moisture, or corrosion is found, return your unit to an Authorized AERIS

Dealer, and DO NOT attempt to use it until it has received factory prescribed service.

BATTERY INSTALLATION

• Lightly lubricate the new Battery Cover O-ring with silicone grease and install it onto the Battery Cover. DO NOT roll the

O-ring over the Threads, instead stretch it slightly to work it down over the slotted end of the Cover into the groove at the base

of the threads (Fig. 98).

• The O-ring must be a genuine AERIS part that can be purchased from an Authorized AERIS Dealer.

Use of any other O-ring will void the warranty.

• Insert a new CR2 Lithium 3 Volt Battery (Duracell or equivalent) positive (+) side ﬁrst into the Battery compartment with the

negative end facing out (Fig. 99).

• Ensure that the Battery is properly installed and the Cover O-ring is evenly seated around the Cover.

• Carefully place the Cover (with spring) into the housing and turn clockwise slowly by hand to ensure proper threading.

• Apply a coin and tighten the Cover by turning it clockwise until secure (Fig. 100). The outer surface of the Cover should be

ﬂush with the outer surface of the housing.

----------------------------------------------------------------------------------------------------------------------------------------------

Fig. 97 - REMOVING THE

BATTERY COVER

Fig. 98 - INSTALLING THE

COVER O-RING

Fig. 99 - INSERTING THE

BATTERY

Fig. 100 - COVER

SECURED

DATA S AV E D

C A L I B R AT E

CO M PA S S

Fig. 96 - CALCULATIONS

& SETTINGS

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Aeris A300 CS Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info