Handleiding Aeris A100 (pagina 6 van 32) (Engels)

618063

Verklein

Vergroot

Pagina terug

1/32

Pagina verder

A100 OPERATING MANUAL

CONTROL BUTTON (B)

The Control Button (B) allows you to select display options and access speciﬁc information when you want to see it.

ACTIVATION & DIAGNOSTICS

A momentary press/release of any button will activate the unit. It will not activate at a depth deeper than 5 FT (1.5 M) or at an

Altitude higher than 14,000 feet.

The unit has contacts that will cause it to activate and enter Dive Mode upon descent to 5 FT (1.5 M) for 5 seconds.

The contacts are the button and the housing screws. Conductivity between any button and any screw (being wet) will satisfy

the activation bridge.

Upon wake up, the unit will check for depth once per second. If depth is not sensed within 10 minutes, it will enter PSM (Power

Saver Mode). Once a dive is made, it will continue checking for depth until the Time to Fly and Time to Desaturate counters

reach 0:00 (hr:min), 24 hours post dive max, and the unit shuts Off.

Immediately following manual (push button) activation (not if by wet activation), all segments of the LCD are displayed (Fig. 1)

followed by a countdown from 8, -, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0 (approx 3 sec). If sensor readings and battery voltage are within

tolerance, the Surface Main screen is displayed (Fig. 2).

If any value is not acceptable, the failure description will ﬂash for 5 seconds for each type failure. If more than one failure is

sensed, the failures will be presented sequentially in the following order.

EEP >> Eeprom error; CAL >> Calibration error; ALT >> higher than 14000 feet or deeper than 5 feet; BAT >> Bat-

tery voltage too low (icon ﬂashing); A-D >> A/d over range

Once the unit is activated, regardless of what mode it is in, it will enter Dive Mode upon descent to 5 FT (1.5 M) for 5 seconds.

While the Surface Main screen is displayed, access to other modes and screens is allowed. They will remain on display for 2

minutes or until the button is pressed to access another mode or screen.

ALPHA / NUMERIC DISPLAYS

It is imperative that you understand the formats, ranges, and values of the information represented to avoid any possible misun-

derstanding that could result in error.

Current Depth is displayed on the Main Dive screens (Fig. 3a).

While at a No Deco Safety or a Deco Stop, the required Stop Depth is displayed on the Main (Fig. 4a).

Max Depth is displayed on Alternate Dive screens (Fig. 5a).

Times are shown in various formats.

• Hour:Minute - Dive Time Remaining (Fig. 3b), Elapsed Dive Time (Fig. 5b), Surface Interval (Fig. 2a), Fly, Sat.

• Minute:Second - Safety Stop Time (Fig. 4b).

Altitude is displayed as a range from L2 to L7 on the Surface Main when at elevations above 3,000 feet. It is not displayed at

Sea level, which extends up to 3,000 feet elevation. Refer to the table on page 23.

POWER SUPPLY

• Battery >> (1) 3 vdc, CR2450, Lithium.

• Shelf life >> up to 5 years.

• Use life >> 100 dive hours if (1) 1 hour dive per dive day up to 300 dive hours if (3) 1 hour dives per dive day.

• Use life >> 300 dive hours if (2) 1 hour dives per dive day.

• Replacement >> by user (annual recommended).

BATTERY STATUS INDICATION

• Warning >> icon on solid (Fig. 6a) when < 2.75 volts, battery change recommended.

• Alarm >> icon on ﬂashing when < 2.50 volts, change the battery.

When the voltage is below that required for normal operation (< 2.50 volts), the graphics CHG and BAT will alternate and the

Battery icon (shell only with no inner bar) will ﬂash once per second for 5 seconds (Fig. 7), then the unit will shut off.

If a Low Battery Warning condition (< 2.75 volts) occurs during a dive, the system will continue to operate with normal displays

and functions throughout that dive.

The Low Battery icon will not be displayed during dives (underwater). It will be displayed when the unit enters Surface Mode.

If a Low Battery Alarm condition (< 2.50 volts) occured during the dive, the graphics CHG and BAT will alternate after 10 min-

utes on the surface, then the unit will shut Off.

Fig. 1 - DIAGNOSTIC

Fig. 2 - SURFACE MAIN

Fig. 4 - STOP DEPTH

Fig. 3 - CURRENT DEPTH

Fig. 5 - MAX DEPTH

Fig. 6 - LOW BATTERY

WARNING

Fig. 7 - LOW BATTERY

(occured during dive)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Aeris A100 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info