3
Replacing the motor lter
Should be done with every 5th replacement of the dust bag,
s-bag ®
1. Open the lid.
2. Remove the old lter (24.).
3. Insert a new lter and close the lid.
Replacement of the micro lter and the non-washable
HEPA lter *
The lter must always be replaced with new ones and cannot
be washed. Should be done with every 5th replacement of the
dust bag, s-bag ®
1. Open and remove the lid (25. ; 26.).
2. Remove the lter and replace it with a new one as
shown in the picture (27. ; 29.).
Important: snap on the lower part of the lter frame rst
then after the upper one. Make sure the sealing is in place.
Cleaning the washable HEPA lter*
Should be done with every 5th replacement of the dust bag,
s-bag®
1. Open and remove the lid, then remove the lter (25. ;
26.).
2. Rinse the inside (dirty side) of the lter in warm tap
water. (28.) Tap the lter frame to remove excess water.
Repeat four times and allow the lter to dry.
Note: Do not use cleaning agents and avoid touching the
delicate lter surface.
3 Replace the lter and lid as shown (27. ; 29.).
Important: snap on the lower part of the lter frame rst
then after the upper one. Make sure the sealing is in place.
Cleaning the hose and nozzle
The vacuum cleaner stops automatically if the nozzle, tube,
hose or lters and s-bag® becomes blocked. In such cases,
disconnect from wall socket and allow to cool for 20-30
minutes. Clear blockage and/or replace lters and s-bag®
and restart.
Cleaning tubes and hose
(30.) Use a cleaning strip or similar to clear the tubes and
hose.
(31.) It may also be possible to remove the obstruction in
the hose by squeezing it. However, be careful in case
the obstruction is caused by glass or needles caught
inside the hose.
Note: The warranty does not cover any damage to the hose
caused by cleaning it.
Cleaning the oor nozzle
(32.) To avoid deterioration of suction power, frequently
clean the carpet/hard oor nozzle. The easiest way to
clean it is by using the hose handle.
Cleaning the turbo nozzle
(certain models only)
(33.) Disconnect the nozzle from the vacuum cleaner tube
and remove entangled threads, etc. by snipping them
away with scissors. Use the hose handle to clean the
nozzle.
(34.) In case the turbo nozzle stops working, open the
cleaning lid and remove any objects that obstructs the
turbine to rotate freely.
(35.) Disconnect the nozzle from the vacuum cleaner tube
and remove entangled threads, etc. by snipping them
away with scissors. Use the hose handle to clean the
nozzle.
Troubleshooting
The vacuum cleaner does not start
1 Check that the cable is connected to the mains.
2 Check that the plug and cable are not damaged.
3 Check for a blown fuse.
The vacuum cleaner stops
1 Check whether the dust bag, s-bag® is full. If so, replace
it with a new one.
2 Is the nozzle, tube or hose blocked?
3 Are the lters blocked?
Water has entered the vacuum cleaner
It will be necessary to replace the motor at an authorised
AEG-Electrolux service centre. Damage to the motor caused
by the penetration of water is not covered by the warranty.
Consumer information
AEG-Electrolux decline all responsibility for all damages
arising from any improper use of the appliance or in cases of
tampering with the appliance.
This product is designed with the environment in mind. All
plastic parts are marked for recycling purposes. For details
see our web site: www.aeg-electrolux.com
Dustbags and accessories!
If you are experiencing diculties in nding the right
dustbag, lter or accessories to your new vacummcleaner
- please call our callcentre (you will nd the number in
the warranty folder) or visit our webshop at www.aeg-
electrolux.com
* Certain models only
