Handleiding Aduro 5-1 (pagina 19 van 33) (Duits, Engels, Deens)

632360

Verklein

Vergroot

Pagina terug

1/33

Pagina verder

- 19 -

3) Keep the door approx. 1 cm ajar, until the glass is too hot to touch. Then close the door. When there are

distinct, visible flames and the fire has taken hold, close the primary air intake/damper.

Important: The control handle will get warm when the fireplace insert is being used. Please use the glove provided

when you operate the fireplace insert.

3.4 The first time a fire is lit

The fireplace is packed in recycling packaging (wood and plastic). This must be disposed according to national

rules regarding disposal of waste. The wood from the packaging can be sawed into smaller pieces and used the

first time a fire is lit.

The first few times the fireplace insert is used, there may be some smoke and unpleasant odours from the fireplace

insert, which is fairly normal. This is caused by the heat-resistant paint hardening. Make sure there is sufficient

ventilation during this stage. It is also important not to let the fire burn too fiercely the first 2–3 times, so that the

fireplace insert has time to expand slowly. You should also be aware that the fireplace insert may make clicking

sounds as it heats up and cools down – rather like pouring boiling water into a sink. These are caused by the great

differences in temperature to which the materials are being exposed.

During the first firing, which should be carried out using approximately 1 kg of wood, the stoking door must be left

slightly open and must not be closed until the fireplace insert is cold. This is to prevent the sealing rope sticking to

the fireplace insert.

3.5 How should I use my fireplace insert?

The fireplace insert is intended for intermittent combustion. This means that each stoking should burn down to

embers before new logs are added.

In order to obtain the best possible combustion, you should regulate the effect/heat output with the fuel. Burning

small logs provides more powerful combustion than burning large logs as the surface area is greater and more gas

is released. The amount of wood in the combustion chamber is another factor that affects combustion. In normal

circumstances, you should not place more than two logs in the fireplace insert. If you want an enhanced effect, you

can add more logs. The nominal heat output is reached by burning approx. 2.2 kg per hour.

3.6 Secondary damper

The secondary damper above the door should always be open while the fireplace insert is in use. This damper

allows you to adjust the fireplace insert to the chimney draft and the heat output you require. In normal

circumstances, the fireplace insert should be working with this damper open between 60 % and 100 %. You should

never close the air intake so far that the flames are extinguished. There should always be visible flames in order to

achieve clean and efficient combustion. The air-wash system, that minimizes soot collecting on the glass panes, is

also adjusted by this damper.

Aduro Key: provides easier control of the secondary damper. The key is fitted onto the control

handle, so you can more easily adjust the airflow from side to side. Turning to the left

decreases the airflow, and turning to the right increases the airflow.

3.7 Primary damper

When you add a new log, the primary air intake/damper should be opened until the fire is burning properly. In order

to utilize the fuel to the fullest extent, the embers should have burnt for so long that it is necessary to open the

primary air intake for approx. 2 minutes to get the new log to burn.

In order to reduce the risk of ash falling from the fireplace insert when the door is opened to add more fuel, it is a

good idea to open the primary air intake/damper for approx. 1 minute before the door is opened. This increases the

draught through the fireplace insert and reduces the risk that ash will drop on the floor.

Please note: if you overload the fireplace insert and burn more than approx. 3.4 kg wood/hour, there is a risk that

the lacquered surface of the fireplace insert will become discoloured and eventually fall off. The fireplace insert can

be resurfaced, but this is not covered by the manufacturer’s guarantee. In the same way, any other damage to the

fireplace insert caused by overloading will not be covered by the guarantee.

3.8 Aduro-tronic

The patent-applied Aduro-tronic is designed to operate the fireplace insert for you. All you

have to do is put dry wood in the fireplace insert, and activate the control system - Aduro-

tronic does the rest, leaving you to enjoy the flames and the benefits of efficient

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Aduro 5-1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info